Baker Hughes Masoneilan 51 Series Скачать руководство пользователя

Страница: 31 / 40

Masoneilan 51/52/53 Series Cylinder Actuator | 31

9. Remove Separator Plate (13), Spring Tube (7) and spring subassembly.

10. Replace the Rod Scraper (34) with a new part. Coat the Rod Scraper with silicone (or equivalent).
11. Replace spring unit, Spring Tube (7), Separator Plate (13), Piston Subassembly (15).

12. Replace the O-ring (21) on the Top Plate (17) and the O-ring (21) and Guide Ring (16) on the Piston Plate S/A

(15) with new parts. Coat the O-rings and Guide Ring with silicone grease (or equivalent).

13. Replace Cylinder Tube (14), and Top Plate (17) with only axial movement. Coat the inner surface of the cylinder

tube with silicone grease.

Figure 16 - Spring Subassembly Removal

Spring Unit

Subassembly

DO NOT

disassemble!

Be careful not to damage the inner surface of the Guide Bushing (8) with the Compression Nut (12)

during assembly.

Be careful not to damage the inner surface of the Guide Bushing (8) with the Compression Nut (12)

during assembly.

Содержание Masoneilan 51 Series





































Результаты поиска

Содержание Masoneilan 51 Series

Отзывы:

Похожие инструкции для Masoneilan 51 Series

Бренды по названию

Популярные бренды

Baker Hughes Masoneilan 51 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Masoneilan 51 Series

Отзывы:

Похожие инструкции для Masoneilan 51 Series

Бренды по названию

Популярные бренды