Baker Hughes DigitalFlow XGF868i Скачать руководство пользователя страница 19

Страница: 19 / 100

Table 4: Transducer signal settings

Transducer signal

parameters

Range

Default

value

Description

Acceleration limit

0 to 250 ft/s

(0 to 76 m/s)

15 ft/s

(5 m/s)

The E6: CYCLE SKIP error message appears when the calculated fluid

velocity changes by more than the programmed ACCELERATION LIMIT

value from one reading to the next. See Chapter 2 in the service manual

for a discussion of error codes.

Amplitude

discriminator low

0 to 100

The amplitude discriminator measures the transducer signal received

by the model XGF868i. The default value for the above parameter is

14, and values from 0 to 100 are acceptable. The E5: AMPLITUDE error

message appears when the amplitude discriminator falls below the

programmed AMP. DISCRIM LOW value. See Chapter 2 in the service

manual for a discussion of error codes.

Amplitude

discriminator high

0 to 100

The amplitude discriminator measures the transducer signal received

by the model XGF868i. The default value for the above parameter is

34, and values from 0 to 100 are acceptable. The E5: AMPLITUDE error

message appears when the amplitude discriminator exceeds the

programmed AMP. DISCRIM HIGH value. See Chapter 2 in the service

manual for a discussion of error codes.

Delta T offset

-1000 to 1000

µsec

0 µsec

An offset between the upstream and downstream transit times is

specified at this prompt.

Skan T offset

–500 to 500

µsec

58 µsec

At this prompt, specify a time measurement offset that compensates

for any shift resulting from cross-correlation. Set to 0 for active skan T

offset.

% of peak

1 to 100%

50%

The percentage of peak used to calculate the transit times and Delta T

is specified at this prompt.

M>S switch

0 to 250 µsec

50µsec

If the burst mode is set to skan/measure (S/M), the meter switches from

skan to measure mode when Delta T is less than the M>S_switch value.

DO NOT change this value unless advised to do so by the factory.

# shifts

0 to 10

The number of shifts corresponds to the actual number of transmits per

cycle (number of signals added together in one direction to produce

an averaged signal for one interrogation of the fluid) and need only be

changed if the environment is very noisy or the acoustic signal is weak.

A divisor

0.1 to 10

2.5

A divisor is used to calculate the measure mode integrated threshold

level and is not normally changed.

# transmit pulses

1 to 16

# transmit pulses specifies the number of pulses in a burst. For difficult

conditions (i.e. long paths, high velocity or high temperature), settings

as high as 16 may be necessary.

T window (cycles)

0 to 1000

The XGF868i calculates the size of the transmit window based on pipe

size and fluid sound speed. However, for diagnostic purposes, the

window size may be reset.

R window (cycles)

10 to 128

The XGF868i calculates the size of the receive window based on pipe

size and fluid soundspeed. However, for diagnostic purposes, the

window size may be reset.

Содержание DigitalFlow XGF868i





































































































Результаты поиска

Содержание DigitalFlow XGF868i

Отзывы:

Похожие инструкции для DigitalFlow XGF868i

Бренды по названию

Популярные бренды

Baker Hughes DigitalFlow XGF868i, Руководство по программированию

Результаты поиска

Содержание DigitalFlow XGF868i

Отзывы:

Похожие инструкции для DigitalFlow XGF868i

Бренды по названию

Популярные бренды