Baker Hughes Consolidated 2478 Series Скачать руководство пользователя страница 17

Страница: 17 / 20

Consolidated 2478 Series Pressure Relief Valve Manual

| 15

Ordering Information

Inlet Size

Type Designation

1.500 - 2478 H - XDAI

Soft Seal

Orifice Designation

XVI. Replacement Parts Planning

The next time replacement parts are needed, keep these

points in mind:

• Baker Hughes designed the parts

• Baker Hughes guarantees the parts

• Consolidated valve products have been in

use since 1879

• Baker Hughes has worldwide service

• Baker Hughes has fast response availability for

parts with the global Green Tag Center (GTC) or

Authorized Consolidated Sales Representatives

network.

XVII. Genuine Consolidated Parts

A. Basic Guidelines

The basic objectives in formulating a replacement parts

plan are:

• PROMPT AVAILABILITY

•   MINIMUM DOWNTIME
•   SENSIBLE COST
•   SOURCE CONTROL

Consult the Recommended Spare Parts list (see Section

XVIII of this manual) to define the parts to be included in

the inventory plan.
Select parts and specify quantities.

B. Identification and Ordering

Essentials

When ordering service parts, please furnish the following

information to ensure receiving the correct replacement

parts:

Specify parts required by:

1.   Part Name (See Figures 1 to 2).
2.   Part Number (if known)
3.   Quantity
Contact your local Green Tag Center (GTC).

Содержание Consolidated 2478 Series




















Результаты поиска

Содержание Consolidated 2478 Series

Отзывы:

Похожие инструкции для Consolidated 2478 Series

Бренды по названию

Популярные бренды

Baker Hughes Consolidated 2478 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Consolidated 2478 Series

Отзывы:

Похожие инструкции для Consolidated 2478 Series

Бренды по названию

Популярные бренды