background image

6  |  

Baker Hughes

© 2020 Baker Hughes Company. All rights reserved.

II.  Safety Alerts

Read -  Understand - Practice

Danger Alerts

A DANGER alert describes actions that may cause 
severe personal injury or death. In addition, it may provide 
preventive measures to avoid severe personal injury or 
death.

DANGER alerts are not all-inclusive. Baker Hughes cannot 

know all conceivable service methods nor evaluate all 
potential hazards. Dangers include:

• 

High temperature/pressure can cause injury. Ensure all 
system pressure is absent before repairing or removing 

valves.

• 

Do not stand in front of a valve outlet when discharging. 
STAND CLEAR OF VALVE to avoid exposure to trapped, 
corrosive media.

• 

Exercise extreme caution when inspecting a pressure 

relief valve for leakage.

• 

Allow the system to cool to room temperature before 
cleaning, servicing, or repairing. Hot components or 
fluids can cause severe personal injury or death.

• 

Always read and comply with safety labels on all 
containers. Do not remove or deface container labels. 
Improper handling or misuse could result in severe 
personal injury or death.

• 

Never use pressurized fluids/gas/air to clean clothing 
or body parts. Never use body parts to check for leaks, 
flow rates, or areas. Pressurized fluids/gas/air injected 
into or near the body can cause severe personal injury 
or death.

• 

It is the owner’s responsibility to specify and  provide 
personal protective wear to protect persons from 
pressurized or heated parts. Contact with pressurized 
or heated parts can result in severe personal injury or 
death.

• 

Do not work or allow anyone under the influence of 
intoxicants or narcotics to work on or around pressurized 
systems. Workers under the influence of intoxicants 
or narcotics are a hazard to themselves and other 
employees. Actions taken by an intoxicated employee 
can result in severe personal injury or death to 
themselves or others.

• 

Always perform correct service and repair.  Incorrect 
service and repair can result in product or property 
damage or severe personal injury or death.

• 

Always use the correct tool for a job. The misuse of a 
tool or the use of an improper tool can result in personal 
injury, damage to product or property.

• 

Ensure the proper “health physics” procedures are 
followed, if applicable, before starting operation in a 
radioactive environment.

Caution Alerts

A CAUTION alert describes actions that may result in a 
personal injury. In addition, they may describe preventive 
measures that must be taken to avoid personal injury. 
Cautions include:

• 

Heed all service manual warnings. Read installation 

instructions before installing valve(s).

• 

Wear hearing protection when testing or operating 

valves.

• 

Wear appropriate eye and clothing protection.

•  Wear protective breathing apparatus to protect against 

toxic materials.

Содержание Consolidated 19000 Series













































Отзывы: