background image

9

Note: The following page is for vehicles with battery’s containing separate electrolyte pack. Most 

battery’s will come with the electrolyte already sealed into the battery.

Preparing the battery:
·  Place battery on level surface. Remove sealing tape 

from top. (see figure 20)

·  Take the electrolyte container out of the plastic bag.
·  Place electrolyte container upside down with the 

sealed silver mouths of the electrolyte bottles in line 

with the six filler holes of the battery. (see figure 21)

·  Push the container down strongly enough to break the 

silver seals.

·  As electrolyte starts flowing into battery, air bubbles 

will come up from the mouths of the plastic electrolyte 

bottles.

·  Leave bottles upside down in battery holes until 

electrolyte is completely drained.

·  Never leave children unattended around battery.

·  If air bubbles cease to float to the top of the electrolyte 

bottles, tap lightly on top.

·  DO NOT remove container from battery while it is 

draining.

·  Never cut or pierce electrolyte container.
·  After all the electrolyte has drained from the bottles 

into the battery, pull plastic electrolyte bottles gently 

out of the battery.

·  Discard empty electrolyte bottles in a waste area that 

is inaccessible to children and animals.

·  After filling let battery stand for at least 30 minutes 

before charging. This allows the electrolyte to 

penetrate plates for optimum performance and ensures 

longer battery life.

·  After 30 minutes the battery is ready for its initial 

charge. Place cap strip loosely over the filling holes as 

shown in the picture. (see figure 22)

Figure 20

Figure 21

Figure 22

Battery Installation

Содержание SC150 HSun 150cc












Отзывы: