background image

INTRODUCTION

HOW TO USE THIS MANUAL

I-E96-435A   

1 - 3

HOW TO USE THIS MANUAL

Read this manual before handling the TM. Refer to the sections
in this list as needed for more information.

1. Read 

Section 2

 before connecting the NIAI03.

2. Refer to 

Appendix A

 for the IMASM03/04 slave module.

3. Refer to 

Section 3

 for the maintenance schedule.

4. Refer to 

Section 4

 and 

Section 5

 when needed.

GLOSSARY OF TERMS AND ABBREVIATIONS

Table 

1-1

 contains the glossary of terms for this manual.

REFERENCE DOCUMENTS

Table 

1-2

 contains the reference documents for the NIAI03.

Table 1-1.  Glossary of Terms and Abbreviations

Term

Definition

Analog

Continuously variable as opposed to discretely variable.

RTD

Resistance temperature detector. A sensing device that changes resistance with 
changes in temperature.

Slave Module

One of a series of modules designed to perform high or low level operations as 
directed by a master module.

TM

Termination Module. Provides input/output connection between plant equipment and 
the INFI 90/Network 90

®

 modules.

TMU

Termination Mounting Unit. A card cage that provides housing for INFI 90/Network 
90 termination modules.

Table 1-2.  Reference Documents

Document 

Number

Description

I-E96-205

Analog Master Module and Analog Slave Modules (IMAMM03 and IMASM01/ 02/03/
04)

I-E96-500

Site Planning and Preparation

® Registered trademark of Elsag Bailey Process Automation.

Содержание Infi 90 NIAI03

























Отзывы: