Bailey Infi 90 IMEDI01 Скачать руководство пользователя страница 24

Страница: 24 / 89

INSTALLATION

JUMPERS (E1 TO E13)

WBPEEUI240759A0

3 - 5

JUMPERS (E1 TO E13)

Verify the jumpers E1 to E13 are set as shown in Table

3-5

for

normal operation. Jumpers E5 to E13 configure the module for
either front panel BNC connection or card edge P3 connection
using an IKED01 cable. Refer to Figure

3-1

for switch, jumper,

and connector locations.

Table 3-4. Example I/O Expander Bus

Address Switch Settings (S6)

Address

Switch Position

1,2

(Binary Value)

(32)

(16)

(8)

(4)

(2)

(1)

NOTES:
1. Switch positions one and two must be ON (closed).

2. 0 = ON or closed; 1 = OFF or open.

Table 3-5. Jumper Settings

(E1 to E13)

Jumper

Setting

Description

Jumper installed

Enable MFT

Jumper removed

Disable MFT

Jumper installed

Enable P6/P7 connectors

Jumper removed

Disable P6/P7 connectors

Jumper installed

TCK signal low

Jumper removed

TCK signal high (floating)

1-2

Enable heartbeat check

2-3

Disable heartbeat check

E5 - E10

1-2

Enable Ethernet signals at P3
connector (card edge)

2-3

Enable Ethernet at BNC
connector (front panel)

E11 - E12

Jumper installed

Enable Et12 VDC at
P3 connector

Jumper removed

Disable Et12 VDC at
P3 connector

E13

Jumper installed

Enable BNC connector

Jumper removed

Disable BNC connector

NOTE:

Bold-italic indicates normal operation setting.

1. For testing purposes only.

Содержание Infi 90 IMEDI01


























































































Результаты поиска

Содержание Infi 90 IMEDI01

Отзывы:

Бренды по названию

Популярные бренды

Bailey Infi 90 IMEDI01, Инструкция

Результаты поиска

Содержание Infi 90 IMEDI01

Отзывы:

Бренды по названию

Популярные бренды