background image

 

 

SAFETY PRECAUTIONS 

 

 

Wood working can be dangerous if safe and proper operating procedures are not followed. As 
with all machinery, there are certain hazards involved with the operation of the product. Using 
the machine with respect and caution will considerably lessen the possibility of personal injury. 
However, if normal safety precautions are overlooked or ignored, personal injury to the operator 
may result. 
Safety equipment such as guards, push sticks, hold-downs, feather boards, goggles, dust 
masks and hearing protection can reduce your potential for injury. But even the best guard won’t 
make up for poor judgment, carelessness or inattention. 

Always use common sense 

and 

exercise 

caution

 in the workshop. If a procedure feel

s dangerous, don’t try it. 

REMEMBER:

 

Your personal safety is your responsibility

 

 

 

Dear Valued Customer: 

  All Baileigh woodworking machines should be used only for their intended use. 

  Baileigh does not recommend or endorse making any modifications or alterations to a 

Baileigh machine. Modifications or alterations to a machine may pose a substantial risk of 
injury to the operator or others and may do substantial damage to the machine. 

  Any modifications or alterations to a Baileigh machine will invalidate the machine's warranty. 

 

Please enjoy your Baileigh machine! ....Please enjoy it SAFELY! 

 
1. 

FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING THE 
MACHINE.

 

Learn the machine’s application and limitations as well as the specific hazards.

 

2. 

Only trained and qualified personnel can operate this machine. 

3. 

Make sure guards are in place and in proper working order before operating 
machinery. 

4. 

Remove any adjusting tools.

 Before operating the machine, make sure any adjusting tools 

have been removed. 

5. 

Keep work area clean.

 Cluttered areas invite injuries. 

6. 

Overloading machine.

 By overloading the machine, you may cause injury from flying parts. 

DO NOT

 exceed the specified machine capacities. 

WARNING:

 FAILURE TO FOLLOW THESE RULES MAY RESULT IN 

SERIOUS PERSONAL INJURY 

Содержание WR-84V-ATC

























































Отзывы: