manualshive.com logo in svg

Baileigh PH-19VS, Руководство оператора

Поделиться
Скачать
Baileigh PH-19VS Скачать руководство пользователя страница 19

17 

17 

LUBRICATION AND MAINTENANCE 

•

Check daily for any unsafe conditions and fix immediately.

•

Check that all nuts and bolts are properly tightened.

•

On a weekly basis clean the machine and the area around it.

•

Lubricate threaded components and sliding devices.

•

Apply rust inhibitive lubricant to all non-painted surfaces.

•

There are 7 grease fittings on the machine. Grease these fittings every month with two

pumps from a standard grease gun.

•

Check for any worn or damaged parts and replace immediately.

•

Check and fill oil cup as needed. Use AW-46 hydraulic oil.

Note

: Proper maintenance can increase the life expectancy of your machine. 

WARNING:

 

Make sure the electrical disconnect is OFF before working on

the machine. 

Maintenance should be performed on a regular basis by qualified personnel. 

Always follow proper safety precautions when working on or around any machinery. 

Содержание PH-19VS








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды