Baileigh Industrial DP-1000G Скачать руководство пользователя страница 7

Страница: 7 / 44

SAFETY INSTRUCTIONS

LEARN TO RECOGNIZE SAFETY INFORMATION

This is the safety alert symbol. When you see this symbol
on your machine or in this manual,

BE ALERT TO THE

POTENTIAL FOR PERSONAL INJURY!

Follow recommended precautions and safe operating practices.

UNDERSTAND SIGNAL WORDS

A signal word

–

DANGER

WARNING

CAUTION

– is used with the safety alert symbol.

NOTICE

, which is not related to personal injury, is used without a symbol.

DANGER

: Indicates a hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING

: Indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION

: Indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

NOTICE

: Indicates a situation which, if not avoided, could

result in property damage.

IMPORTANT

PLEASE READ THIS OPERATORS MANUAL CAREFULLY

It contains important safety information, instructions, and necessary operating procedures.
The continual observance of these procedures will help increase your production and
extend the life of the equipment.

DANGER

WARNING

CAUTION

NOTICE

Содержание DP-1000G













































Результаты поиска

Содержание DP-1000G

Отзывы:

Похожие инструкции для DP-1000G

Бренды по названию

Популярные бренды

Baileigh Industrial DP-1000G, Руководство оператора

Результаты поиска

Содержание DP-1000G

Отзывы:

Похожие инструкции для DP-1000G

Бренды по названию

Популярные бренды