Baicells mBS31001 Скачать руководство пользователя страница 9

Страница: 9 / 22

LTE TDD Base Station Installation Guide

Item

Description

MTBF

≥ 150000 hours

MTTR

≤ 1 hour

Maintenance

Support remote/local maintenance, based on SSH

protocol

Support remote maintenance

Support online status management

Support performance statistics

Support failure management

Support configuration management

Support local or remote software upgrading and loading

Support log

Support connectivity diagnosis

Support automatic start and configuration

Support alarm reporting

Support

KPI Recording

Support

user information tracing

Support

signaling trace

1.4.3 Environment Specification

Item

Description

Operating Temperature

-40°C to 55°C

Storage Temperature

-45°C to 70°C

Humidity

5% to 95%

Atmospheric Pressure

70 kPa to 106 kPa

Ingress Protection Rating

IP66

Power Interface Lightning Protection

Differential mode: ±10KA

Common mode: ±20KA

1.4.4 FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

Any Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Содержание mBS31001






















Результаты поиска

Содержание mBS31001

Отзывы:

Похожие инструкции для mBS31001

Бренды по названию

Популярные бренды

Baicells mBS31001, Руководство по установке

Результаты поиска

Содержание mBS31001

Отзывы:

Похожие инструкции для mBS31001

Бренды по названию

Популярные бренды