Baicells BRU35 Series Скачать руководство пользователя страница 28

Nova-243 Outdoor LTE TDD Base Station Installation Guide 

22 

 

Any  Changes  or  modifications  not  expressly  approved  by  the  party  responsible  for 

compliance could void the user's authority to operate the equipment. 

This equipment has been tested and found to comply with the limits for a Class B digital 

device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide 

reasonable  protection  against  harmful  interference  in  a  residential  installation.  This 

equipment  generates  uses  and  can  radiate  radio  frequency  energy  and,  if  not  installed 

and  used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio 

communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a 

particular  installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or 

television  reception,  which  can be  determined  by  turning  the  equipment  off  and  on,  the 

user  is  encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the  following 

measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the 

receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

Warning: 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 

environment.  This  equipment  should  be  installed  and  operated  with  minimum  distance 

30cm between the radiator & your body. 

 

ISEDC Compliance 

This device complies with Innovation, Science, and Economic Development 

Canada licence-exempt RSS standard(s).  

Operation is subject to the following two conditions: (1) This device may not cause in

terference, and (2) This device must accept any interference, including interference t

hat may cause undesired operation of the device. 

 

Le présent appareil est conforme aux CNR d' Innovation, Science et Développement 

é

conomique Canada applicables aux appareils radio exempts de licence. 

L'exploitation est autorisée aux deux conditions  

suivantes:   

(1) l'appareil ne doit pas produire de brouillage, et  

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,  

Содержание BRU35 Series






























Отзывы: