Badland Winches 63476 Скачать руководство пользователя | Manualshive

Страница: 14 / 16

background image

Page 14

For technical questions, please call 1-888-866-5797.

Item 63476

S

AFET

y

O

PERA

TION

M

AINTENANCE

S

ETUP

Troubleshooting

Problem

Possible Causes

Likely Solutions

Motor overheats.

1. Incorrect power cords.
2. Winch running time too long.

1. Use only supplied power cords.
2. Allow winch to cool down periodically.

Motor does
not turn on.

1.  Remote battery dead.
2.  Loose battery cable connections.
3.  Vehicle battery needs charging.
4.  Solenoid malfunctioning.

5. Remote damaged.
6. Defective motor.

7. Water has entered motor.

8. Internal damage or wear.

1.  Replace Remote battery.
2.  Tighten nuts on all cable connections.
3.  Fully charge battery.
4.  Tap solenoid to loosen contacts.

Apply 12 volts to coil terminals directly.
A clicking indicates proper activation.

5. Replace Remote.
6. Check for voltage at armature port with Switch

pressed. If voltage is present, replace motor.

7. Allow to drain and dry. Run in short bursts

without load until completely dry.

8. Have technician service winch.

Motor runs but
Wire Rope drum
does not turn.

Clutch not engaged.

Move the Clutch Knob to the Engaged position.

If problem persists, a qualified technician
needs to check and repair.

Motor runs
slowly or without
normal power.

1. Insufficient current or voltage.

2. Loose or corroded battery

cable connections.

3. Incorrect power cords.

1. Battery weak, recharge.

Run winch with vehicle motor running.

2. Clean, tighten, or replace.

3. Use only supplied power cords.

Motor runs in one
direction only.

1. Defective or stuck solenoid.

2. Remote damaged.

1. Tap solenoid to loosen contacts.

Repair or replace solenoid.

2. Replace Remote.

Follow all safety precautions whenever diagnosing or servicing

the tool. Disconnect power supply before service.

PLEASE READ THE FOLLOWING CAREFULLy

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

«
...
12
13
14
15
16
»

Содержание 63476

















Отзывы:

Нет отзывов

Похожие инструкции для 63476

Бренд: Quadratec Страницы: 12

Бренд: Westfalia Страницы: 23

Бренд: Allied Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды