Badger Meter ModMAG M1000 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 52

Badger Meter ModMAG M1000 Скачать руководство пользователя страница 24

Programming

Page 22/47

MID_M1000_BA_02_1802

5.1.3 Input and outputs

Analog output

Range

This parameter establishes the range of the analog

output signal: 0 to 100% (= full scale). The following cur-

rent ranges are available to you:

Analog output active

Analog output passive

Note:
In case that an error message is displayed, the current is

set according the programing of the “Alarm Mode” below.
In case that you select bidirectional operation, you can

signal flow direction via digital outputs.
This parameter configures the behaviour of the analog

output during alarm conditions. Three options exist for

this parameter:

OFF, LOW and HIGH

.

OFF:

Analog signal is based on flow rate and always

within the configured range.

LOW:

During alarm conditions, the analog signal will be

2 mA less than the configured lower range. (only on

4-20 mA range).

HIGH:

During alarm conditions, the analog signal will be

2 mA more than the configured upper range.
For example, if the analog range is 4 to 20 mA and the

alarm mode is set to HIGH, then during a full scale flow

alarm condition, the analog output current will be 22 mA.

Alarm Mode

Current output
0 to 20 mA
4 to 20 mA
0 to 10 mA

«
...
22
23
24
25
26
...
»

Содержание ModMAG M1000





















































Отзывы:

Нет отзывов