Badger Meter M-series Скачать руководство пользователя

Страница: 47 / 56

Page 47

4-11

Installation & Operation Manual

Info/Help

Error Counts

[0]

Description

This menu provides a diagnostic view of the meter’s performance. Below are several

system diagnostic counters and their definitions. Use discretion when interpreting

these counters. These values could be altered during system setup or when using

the verification device. We suggest that you reset these counters before you start

monitoring your system and look for conditions possibly affecting performance.

Detector

The number of times an invalid detector condition has been observed.

Empty Pipe

The number of times an empty pipe condition has been observed by the meter.

Full Scale

The number of times the flow has exceeded the full scale flow setting.

Totalizer

The number of times the totalizers have exceeded limits of the meter.

Pulse Sync.

The number of times the pulse outputs have fallen out of synchronization.

ADC Interrupt

The number of times an analog input measurement has been missed.

ADC Range

The number of times the analog input measurement range has been exceeded.

System Error

A diagnostic system message indicating the reason for a system reset.

System Resets

The number of times the meter has been reset.

System Reset ID

Diagnostic information about a system reset as a result of expired internal timers.

Содержание M-series

























































Результаты поиска

Содержание M-series

Отзывы:

Похожие инструкции для M-series

Бренды по названию

Популярные бренды

Badger Meter M-series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание M-series

Отзывы:

Похожие инструкции для M-series

Бренды по названию

Популярные бренды