background image

Dimensions

Intrinsically Safe Electrical Installation 

The Series 200 sensor is approved, as an entity, as intrinsically safe when installed in conformance with Badger Meter 

installation drawings 06-480-001 or 06-480-002 (sample shown in 

"Impeller Assembly and Shaft Replacement" on page 9

) as 

specified on the blue label identifying an intrinsically safe sensor . 
Entity approval implies that only the sensor is approved as intrinsically safe . Unless power supplies, equipment, and 

instruments connected to the sensor are each rated either explosion-proof or intrinsically safe, these devices cannot be 

installed in a hazardous area . The referenced installation drawing shows such apparatus located in a non-hazardous location . 

Proper interfacing between the hazardous and non-hazardous areas must be provided . This interface must be constructed 

and all wiring must be performed by qualified contractors . To make sure the installation is intrinsically safe, the connection of 

the intrinsically safe sensor to instruments and or power supplies must take place using an approved intrinsically safe barrier 

located in a nonhazardous area . These barriers, listed below, are readily available from various suppliers .

Manufacturer

Barrier

Crouse-Hinds Spec 504

Cat No . SB19140M0715

Measurement Technology Ltd .

MTL 715+ 15 V

R Stahl Intrinspak

9001/01-158-150-101

DIMENSIONS

Series No. Complete

228PV15XX-XXX

228PV2XXX-XXXX

228PV3XXX-XXXX

228PV4XXX-XXXX

A5 

B5 

C2 

D3 

E5

5 .0 in . (127 mm) 

5 .16 in . (131 mm) 

2 .38 in . (60 mm) 

3 .97 in . (101 mm) 

5 .0 in . (127 mm)

5 .63 in . (143 mm) 

5 .64 in . (143 mm) 

2 .88 in . (73 mm) 

4 .20 in . (107 mm) 

5 .0 in . (127 mm)

6 .50 in . (165 mm) 

6 .83 in . (173 mm) 

4 .23 in . (107 mm) 

4 .68 in . (119 mm) 

5 .0 in . (127 mm)

7 .38 in . (187 mm) 

6 .83 in . (199 mm) 

5 .38 in . (137 mm) 

5 .10 in . (130 mm) 

5 .0 in . (127 mm)

E

D

B

A

C

No Fittings

E

D

B

A

C

BSP Fittings

E

D

B

A

C

Flanged (4 in . only)

Figure 1:  A = Overall Length; B = Overall Height; C = Diameter;  

D = Center of Tube to Top Height; E = Minimum Clearance for Sensor Removal

Page 7 

February 2018

SEN-UM-01664-EN-10

Содержание Impeller Data Industrial 228PV Series













Отзывы: