Bad Boy Mowers EXTREME страница 31 Скачать руководство пользователя | Manualshive

Страница: 31 / 72

background image

PAGE 31

275 YAMAHA

(CONTINUED)

The air cleaner is the engine’s only defense against

damaging foreign particles. It is very important that the air

cleaner element is inspected prior to each use. Remove

the element and tap its sides in order to remove debris.

Do not blow the filter out using compressed air. Doing so

will greatly reduce the air cleaner’s effectiveness.

Replace yearly; more often in dusty environments.

Adhering to these practices will help prevent loss of

power and premature engine failure.

CHANGING THE AIR CLEANER

1.

Unlock the air cleaner cover and remove to

access the air cleaner.

2.

Remove the outer and inner air filters.

3.

Replace inner and outer filter then place the inner

filter into the air intake followed by fitting the

outer filter over the inner filter.

4.

Install onto base and place cover back on and

lock into place.

«
...
29
30
31
32
33
...
»

Содержание Mowers EXTREME









































































Отзывы:

Нет отзывов

Похожие инструкции для Mowers EXTREME

Бренд: Kärcher Страницы: 444

Бренд: Lawn-Boy Страницы: 24

Бренд: Lawn-Boy Страницы: 84

Бренд: Lawn-Boy Страницы: 20

Бренд: Lawn-Boy Страницы: 20

Бренд: Lawn-Boy Страницы: 16

Бренд: Gardena Страницы: 9

18.5HP Z-Force 42

Бренд: Cub Cadet Страницы: 56

Бренд: Gardena Страницы: 52

EC Hydro Midsize

Бренд: Ransomes Страницы: 54

Бренд: Powersmart Страницы: 73

Бренд: KUHN Страницы: 72

Бренд: MASCOT Страницы: 8

Бренд: Ryobi Страницы: 272

Бренд: Snapper Страницы: 44

Бренд: Hyundai Страницы: 46

Бренд: Nakayama Страницы: 80

Бренд: Cub Cadet Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды