Bad Boy Mowers EXTREME страница 29 Скачать руководство пользователя

Страница: 29 / 72

PAGE 29

275 YAMAHA

This machine has an oil drain hose installed on the

engine to allow for easier oil changes. Bad Boy

recommends that the oil and filter be changed after the

initial 8 hrs. of use, and at intervals of 50 usage hours or

yearly, whichever occurs first after that. The oil capacity is

2 quarts. Bad Boy 10W-30 synthetic blend engine oil is

recommended for maximum protection.

CHANGING YOUR ENGINE OIL AND OIL FILTER

Remove oil dipstick and open oil drain. Allow oil

to completely drain. (Make sure to have an oil

pan ready to capture old oil and properly dispose

old oil.)

The oil filter is located on the right side of the

engine. Clean area around oil filter. Place a

container under the oil filter to capture any oil and

remove filter. Wipe off mounting surface and

reinstall drain plug. Torque to 10ft.-lb. Place new

filter in shallow pan with open end up. Fill with

new oil until oil reaches the bottom of the

threads. Allow 2 minutes for oil to be absorbed by

filter material.

Apply a thin film of clean oil to rubber gasket on

new filter

Refer to instructions on oil filter for proper

installation.

Fill crankcase with approximately 2 quarts of new

oil. Level should top of indicator on dipstick.

Reinstall oil fill/dipstick and tighten securely.

Start engine; check for oil leaks. Stop Engine;

correct oil leaks. Re-check oil level

Dispose of used oil and filter in accordance with

local ordinances.

Содержание Mowers EXTREME









































































Результаты поиска

Содержание Mowers EXTREME

Отзывы:

Похожие инструкции для Mowers EXTREME

Бренды по названию

Популярные бренды

Bad Boy Mowers EXTREME, Руководство владельца, обслуживания и запасных частей

Результаты поиска

Содержание Mowers EXTREME

Отзывы:

Похожие инструкции для Mowers EXTREME

Бренды по названию

Популярные бренды