Backyard Products Heartland MANSFIELD GABLE Скачать руководство пользователя страница 5

Страница: 5 / 72

OPTIONAL MATERIALS

DRIP EDGE ..................... 60 Feet

#15 ROOFING FELT

To cover 148 Sq. Ft. of roof area.

1" GALVANIZED ROOFING NAILS.........1/4 Lb

For roofing felt.

REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER’S

INSTRUCTIONS FOR INSTALLATION OF SHINGLES, DRIP EDGE AND FELT.

COMPLETING YOUR SHED

You will need these additional materials:

3-TAB SHINGLES ............................. 7 Bundles

PAINT FOR SIDING .......................... 2 Gallons

Use 100% acrylic latex exterior paint. (2) coats recommended.

CAULK ................................................. 3 Tubes

Use acrylic latex exterior caulk that is paintable.

1" GALVANIZED ROOFING NAILS.... 3 Lbs

For shingles.

PAINT FOR TRIM .............................1 Quart

Use 100% acrylic latex exterior paint.

WOOD GLUE ....................... Exterior Rated

REINFORCED WOOD FLOOR FRAME (OPTIONAL)

WOOD FLOOR FRAME

IMPORTANT!

The included floor has been designed for general use. Depending on your specific use you may want to construct a

heavy duty floor frame by adding additional floor joists (shown below as shaded). Below is a list of additional materials (not included):

x12

2 x 4 x 10' (5 x 10 x 304,8 cm) Treated Lumber

Cut to (3) 2 x 4 x 117" (5 x 10 x 297,2 cm)

ea. 3" (7,6 cm) Hot Dipped Galvanized Nails

Optional 12" (30,5 cm) spacing

Standard 16" (40,7 cm) spacing

FOUNDATION OR FLOOR MATERIALS

ADDITIONAL MATERIALS

• This shed does not include any floor or leveling materials.
• See the FLOOR LEVELING section on page 8 for recommended methods and suggested materials to properly level your

floor, as this will vary depending on your specific site.

NOTE: Use a minimum of 5/8" (1,6 cm) Oriented Strand Board (OSB)

5/8" x 48" x96"

(1,6 x 121,9 x 243,8 cm)

FLOOR PANELS

You will need floor panels and nails to complete your floor.

Floor panel sizes and quantities are shown below.

2" (5,1 cm)

1 lb. of 2" (5,1 cm) Hot

Dipped Galvanized

Box-Type Nails.

MATERIAL REQUIRED:

Use only wood treated for ground contact and fasteners approved for use with treated wood.

x12

2 x 4 x 120" (5,1 x 10,2 x 304,8 cm)

Hot Dipped Galvanized Box-Type Nails.

3" (7,6 cm)

x44

2 x 4 x 144" (5,1 x 10,2 x 365,8 cm)

Содержание Heartland MANSFIELD GABLE









































































Результаты поиска

Содержание Heartland MANSFIELD GABLE

Отзывы:

Похожие инструкции для Heartland MANSFIELD GABLE

Бренды по названию

Популярные бренды

Backyard Products Heartland MANSFIELD GABLE, Руководство пользователя

Результаты поиска

Содержание Heartland MANSFIELD GABLE

Отзывы:

Похожие инструкции для Heartland MANSFIELD GABLE

Бренды по названию

Популярные бренды