Backflow Direct Deringer 20 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 20

Backflow Direct Deringer 20 Скачать руководство пользователя страница 1

4X”– 6” Deringer 20/30 Maintenance Instructions

At Backflow Direct we are committed to making our products as easy to install as possible. We design for
most contingencies, but installation may be different based on your regional regulations or system design.

We are continually improving our products and instructions

– please help us by providing recommendations

as to how we can improve or products or instructions.

If you have any difficulties at all, please give us a call. Thank you for purchasing our product!

IMPORTANT NOTE: We use Stainless Steel Hardware where possible. Therefore, it is best to have Silver Anti-
seize available to use on all non-wetted bolts

—only a small amount is needed.

WARRANTY INFORMATION:

Please visit our website for our official warranty www.backflowdirect.com/warranty

READ INSTRUCTIONS IN FULL BEFORE INSTALLATION.

QUESTIONS? CALL 916-760-4524 M-F 8:00 AM

– 4:30 PM PST

REV: A | 09/06/2019 | BD-INST-4X2030

1
2
3
...
»

Содержание Deringer 20





















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды