manualshive.com logo in svg

Bacharach 6401-0500, Инструкция по установке и эксплуатации

Поделиться
Скачать
Bacharach 6401-0500 Скачать руководство пользователя страница 59

MGS-250 Manual 

 

 

6490-9000 Revision 3 

59 

 
 
 
 

  D

ECLARATION

 

OF

 C

ONFORMITY

 

 

 

The manufacturer of the 
products covered by this 
declaration: 

Bacharach,  Inc. 

621 Hunt Valley Circle 

New Kensington, PA  15068 

Year conformity is 
declared: 

2013 

Product(s): 

Refrigerant Gas Monitor/Transmitter 

Model(s): 

MGS-250 

 

The undersigned hereby declares that the above referenced products are in conformity 
with the provisions of the following standard(s) and is in accordance with the following 
directive(s). 

 

Directive(s): 

2004/108/EC 

Electromagnetic Compatibility (EMC) Directive 

2006/65/EC 

Low Voltage Directive (LVD) 

 

Standard(s): 

EN 50270:2006 

Electromagnetic compatibility –  electrical apparatus for the 
detection and measurement of combustible gases, toxic gases 
or oxygen 

EN 55011:2007 

Limits and methods of measurement of electromagnetic 
disturbance characteristics of industrial, scientific and medical 
(ISM) radio frequency equipment 

IEC 61010-1:2010 

EN 61010-1:2010 

Safety requirements for electrical 

equipment for 

measurement, control, and laboratory use –  Part 1: General 
requirements 

 
 

Signature:  

 

 

Name:

 

Aaron Kennison 

Title:

 

Engineering Manager 

Date:

 

3 July 2013 

 

The technical documentation file required by this directive is maintained at the corporate 

headquarters of Bacharach, Inc. 

Содержание 6401-0500





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды