Bacharach 24-7233P Скачать руководство пользователя страница 14

Страница: 14 / 44

Instruction 24-9435

Fyrite Tech

3.4 Front Panel Pushbuttons

Note that a pushbutton may perform several functions, depending on what
screen is being displayed at the time.

I/O

•

Turns analyzer ON/OFF. There is a 60 second warm-up and
a 5 second turn-off-delay period.

•

Places the analyzer into either its Setup or Calibration Mode

when used in conjunction with the

ENTER

HOLD

button.

▲

•

Scrolls up through the display screens during a test.

•

Causes the displayed value to increase or change while in

the Calibration or Setup Mode.

▼

•

Scrolls down through the display screens during a test.

•

Causes the displayed value to decrease or change while in

the Calibration or Setup Mode.

ENTER

•

Enters the Run Mode (starts a combustion test) from the

Fuel Select Screen.

•

Displays the Fuel Select Screen when held down for 2 sec-

onds while in the Run Mode.

•

Stores the displayed value and automatically steps to the

next screen when pressed during calibration or setup.

•

Sets up the analyzer to be placed into its Calibration Mode

when held down with the analyzer OFF. (Used in conjunc-
tion with the

I/O

button.)

•

Places the unit into its Run Mode when held down for 2 sec-

onds while in the Calibration Mode.

•

Aborts turn-off and keeps the analyzer turned ON when

pressed during the 5 second turn-off-delay period.

HOLD

•

Freezes the display during a test, allowing the op er a tor to

scroll through the displays and view all test values at that
point in time.

•

Sets up the analyzer to be placed into its Setup Mode when
held down with the analyzer OFF. (Used in conjunction with
the

I/O

button.)

LIGHT

Toggles the back light ON and OFF.

Содержание 24-7233P













































Результаты поиска

Содержание 24-7233P

Отзывы:

Бренды по названию

Популярные бренды

Bacharach 24-7233P, Инструкция по эксплуатации

Результаты поиска

Содержание 24-7233P

Отзывы:

Бренды по названию

Популярные бренды