Bacharach 0024-8252 Скачать руководство пользователя страница 5

Страница: 5 / 76

Fyrite INSIGHT

1.0 INTRODUCTION

1.1 The Fyrite

INSIGHT

The Fyrite

INSIGHT is a hand-held residential and commercial grade

portable combustion analyzer that is designed for on-demand sampling of

light industrial combustion equipment, residential furnaces, and appli-

ances.

The following conventions are used in this manual:

WARNING:

A warning statement denotes a potential hazard

associated with the use of this equipment. Failure to follow this

information could result in serious personal injury or death.

CAUTION:

A caution statement indicates a potentially hazardous

situation which, if not avoided, may result in minor or moderate in-

jury. Caution statements may also be used to alert against unsafe

practices.

To assure operator safety and the proper use of the Fyrite INSIGHT,

please read the contents of this manual for important information on the

operation and maintenance of the analyzer. This manual contains infor-

mation on all models of the Fyrite INSIGHT. Please disregard any infor-

mation that does not pertain to your model.

WARNINGS!

• This analyzer should not be used on a continuous basis.

• This analyzer should not be used as a safety device.

• Except for sensor and battery replacement, this analyzer should only be

opened and serviced by authorized personnel.

• When testing an appliance, a full visual inspection of the appliance

should be carried out to ensure its safe operation.

• HAZARDOUS AREA WARNING: This instrument has not been de

signed to be intrinsically safe for use in areas classified as hazardous

locations. For your safety, DO NOT use it in hazardous (classified) loca

tions.

Содержание 0024-8252













































































Результаты поиска

Содержание 0024-8252

Отзывы:

Похожие инструкции для 0024-8252

Бренды по названию

Популярные бренды

Bacharach 0024-8252, Инструкция по эксплуатации

Результаты поиска

Содержание 0024-8252

Отзывы:

Похожие инструкции для 0024-8252

Бренды по названию

Популярные бренды