background image

ELECTRICAL SAFETY

Each motor associated with this equipment should be installed with a lockable disconnect switch located within

sight of the equipment. No service work should be performed on or near the fans, motor, drives or inside the

equipment unless motors, heaters etc. are electrically isolated.
Each fan associated with this equipment should be installed with a lockable disconnect switch located within sight

of the equipment. No service work should be performed on or near the fans unless motors are electrically isolated.

LIFTING

Caution

FAILURE TO USE DESIGNATED LIFTING POINTS CAN RESULT IN A DROPPED LOAD

CAUSING SEVERE INJURY, DEATH AND/OR PROPERTY DAMAGE. LIFTS MUST BE

PERFORMED BY QUALIFIED RIGGERS FOLLOWING BAC PUBLISHED RIGGING

INSTRUCTIONS AND GENERALLY ACCEPTED LIFTING PRACTICES. THE USE OF

SUPPLEMENTAL SAFETY SLINGS MAY ALSO BE REQUIRED IF THE LIFT CIRCUMSTANCES

WARRANT ITS USE, AS DETERMINED BY THE RIGGING CONTRACTOR.

LOCATION

All cooling equipment should be located as far away as possible from occupied areas, open windows or air intakes

to buildings.

Caution

EACH UNIT SHOULD BE LOCATED AND POSITIONED TO PREVENT THE INTRODUCTION

OF DISCHARGE AIR INTO THE VENTILATION SYSTEMS OF THE BUILDING ON WHICH THE

UNIT IS LOCATED OR THOSE OF ADJACENT BUILDINGS.

For detailed recommendations on BAC equipment layout, please see the BAC Application Handbook EU-

Edition, the BAC website: www.baltimoreaircoil.eu or contact your local BAC-Balticare Representative.

LOCAL REGULATIONS

Installation and operation of cooling equipment may be subject to local regulations, such as establishment of risk

analysis. Ensure regulatory requirements are consistently met.

Non-walking Surfaces

Access to and maintenance of any component needs to be performed in accordance with all local applicable laws

and regulations. If the proper and required access means are not present, temporary structures need to be

foreseen. Under no circumstance can one use parts of the unit, that are not designed as an access mean, unless

measures can be taken to mitigate any risks that might occur from doing so.

W W W . B A L T I M O R E A I R C O I L . E U

9

1 General Information

1 General Information

Содержание S1500E





























Отзывы: