Weekly Maintenance:
1. Repeat steps 1 to 3 from the Daily
Maintenance cleaning steps.
2. Rinse the foil head under running water
(see Fig. 5).
NEVER submerge the shaver body in
water.
3. Leave head detached for drying.
4. Press the shaver head back into place
(see Fig. 4).
5. Make sure the magnetic contacts on the
cap are clean, using alcohol to clean
any debris or buildup.
HIDDEN HANGING HOOK
The shaver has a sliding hanging hook that
is built into the bottom of the unit next to
where the battery is removed and installed.
1. To use the hook, simply pull out with
enough force to feel a click, which will
lock it in place.
2. When not using the hook, push it back
into the base of the shaver, and it will
click into place, staying hidden until you
want to use it again.
USER MAINTENANCE
INSTRUCTIONS
TAKING CARE OF YOUR SHAVER
Do not remove the shaving foil head while
the shaver is switched on. Always switch
the shaver off before removing head!
Ensure that no water gets into the inside of
the shaver to avoid the risk of an electric
shock when it is back in operation.
Never press on the cutters or the double
shaving foil and do not touch them with
hard objects, as this can cause irreparable
damage to the shaver or its parts.
Be careful when dealing with the cutters,
as they are very sharp. Risk of injury!
When cleaning, do not apply any detergents
or scouring agents and do not use any
abrasive or sharp objects. They can cause
irreparable damage to the shaver.
NOTE:
WHEN CLEANING YOUR SHAVER,
MAKE SURE IT IS TURNED OFF.
CAUTION!
•
DO NOT run shaver, cutters or cap
under water. Use only the small brush
(included) to clean the cutters.
• To clean the external surfaces of the
shaver, use a damp cloth. DO NOT APPLY
ANY DETERGENTS.
• To dry, wipe the surface of the shaver
with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
• The shaver should not be used until it
has completely dried.
Daily Maintenance:
1. First remove magnetic cap from shaver.
Then remove the foil head assembly (see
Figs. 1 & 2). For complete instructions
on how to remove foil head, see TO
REPLACE FOIL HEAD ASSEMBLY.
2.
Use cleaning brush to whisk away
any debris on and around the cutters
(See Fig. 3).
3. Snap the head assembly closed (see
Fig. 4).
Fig. 2
Fig. 1
Fig. 3
Fig. 4
Fig. 5
Washable
NOTE: Always replace the cutters and
foil head assembly at the same time.
TO REPLACE FOIL HEAD ASSEMBLY
1. To remove the foil head assembly, hold
the ribs of foil head assembly on both
sides and lightly pull up at one side and
away from shaver body (see illustrations
below).
2. Take the replacement foil head assembly
out of package. Align the replacement
foil head assembly over the cutters.
Carefully move the replacement foil
head assembly down toward the shaver
unit until it firmly snaps into place.
BE
CAREFUL NOT TO DAMAGE THE FOILS
OR CUTTERS WHILE INSTALLING.
4
5
TO REPLACE CUTTERS
1. First remove foil head assembly. Then
remove one cutter by placing your
fingers on each side of it and gently
pulling up and away from the drive
shaft. Repeat with second cutter.
2.
Remove the new cutters from the
packaging. Align one cutter above a
drive shaft and lightly push down until
it snaps into place. Repeat with second
cutter.
3. Replace the foil head assembly, then
turn shaver on to ensure it is working
properly.
GOOD
BAD
BENT
BENT
Always check to be sure the cutters are not
bent in any way.
B79FSG(MB)A IB-23_450.indd 3
B79FSG(MB)A IB-23_450.indd 3
2024/1/8 15:00
2024/1/8 15:00
