Baby Lock BLKF Скачать руководство пользователя страница 2

Страница: 2 / 28

2 Baby Lock Kinetic Frame Assembly Instructions

Table of Contents

Page
3. Parts & Hardware List

6. Step 1- Remove Track Supports

7. Step 2- Table Assembly

8. Step 3- End Leg Assembly

11. Step 4- Middle Leg Assembly

13. Step 5- Rotate the Frame

14. Step 6- Support Rail Assembly

15. Step 7- Track Assembly

18. Step 8- Ratchet Stop Assembly

20. Step 9- Pole Bracket Assembly

21. Step 10- Pole Coupler Assembly

22. Step 11- Pole End Assembly

25. Step 12- Batting Bar Bracket Assembly

26. Step 13- Pole to Frame Assembly

26. Step 14- Rubber End Cap Assembly

27. Step 15- Bungee Clamp Assembly

27. Step 16- Hook & Loop Tape on Pole Assemblies

28. Step 17- Attach Leaders

28. Step 18- Adjusting Frame Height and Leveling

Baby Lock Kinetic Frame

What’s Included

Your Baby Lock Kinetic Frame is delivered in three separate boxes. Upon opening, please check

immediately to see if you have received the items listed in the Parts and Hardware lists found on

pages 3, 4 and 5.

Box 1:

(2) Two table top frame assemblies, each with (1) QF05300-301 table frame

(1) QF05300-302 table top

(2) QF05300-02 track supports

(6) QF09318-303 track support screws

Box2:

Includes frame support, brackets and all other parts and hardware

(1) Baby Lock Kinetic Frame Assembly Instructions

(3) Hook and loop tapes to attach leaders to poles

(Baby Lock Leaders (Part # BLQL) are sold separately.)

Box 3:

(10) QF05300-701 poles

(5) QF09318-702 pole couplers

(2) QF05300-150 Support Rails

Содержание BLKF





























Результаты поиска

Содержание BLKF

Отзывы:

Похожие инструкции для BLKF

Бренды по названию

Популярные бренды

Baby Lock BLKF, Руководство по сборке

Результаты поиска

Содержание BLKF

Отзывы:

Похожие инструкции для BLKF

Бренды по названию

Популярные бренды