1
OMA01C
Congratulations on your purchase of the BOB Handlebar Console. It is designed to provide beverage holders and additional storage. Proper
installation and care will provide years of reliable service.
Before attempting to install your new Handlebar Console, read and understand these instructions completely to insure proper
installation. If you are unclear on any point, contact your dealer or BOB before use.
WARNINGS
FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
• This product is not designed to hold hot beverages. Placing hot beverages in the cup holders can result in spills and injury to you or your
child, including burns.
• When placing containers in the cup holders, it is critical that at least 60% of the container be inserted in the beverage holder so containers
do not come out.
• The Handlebar Console is designed exclusively for use with BOB single strollers. It is not intended for use with other strollers or products.
• Never exceed 2lbs total in handlebar console. Exceeding 2lbs can create an unstable condition and cause your stroller to tip over - leading
to injury.
INSTALLATION INSTRUCTIONS
If your stroller has
RED
Handlebar Release Levers as shown below:
Go to step 4.
1.
Begin by orienting the Handlebar Console as shown in Fig. 1.
2.
The Handlebar Console attaches to the stroller handlebar by four Velcro straps. Start attaching the Handlebar Console to the handle bar
with the front right Velcro strap, “A” in Fig. 1. The strap attaches as follows:
a.
Align the strap with the forward edge of the handlebar foam. Route the strap underneath the handlebar, being careful not to wrap the
strap around the black handlebar release lever or brake cable housing (if equipped with hand
brake).
It is critical that the Velcro straps not wrap around the black rod, brake cable
housing or handlebar release lever. Wrapping the straps around the black rod can interfere
with the correct function of the handlebar release system resulting in the handlebar
unexpectedly releasing, causing loss of control and injury.
Wrapping the straps around the brake cable housing can interfere with the
proper function of the brake causing loss of control and injury.
Wrapping the straps around the handlebar release levers can interfere with the correct
function of the handlebar release system resulting in the handlebar unexpectedly releasing,
causing loss of control and injury.
Correct routing of the Velcro strap is shown in PHOTO B-1.
b.
Continue wrapping the Velcro strap around the handlebar and insert through the black plas-
tic ring as shown in Fig. 4.
c.
Loop the Velcro strap through the ring and secure as shown in Fig. 5.
d.
Repeat above steps (a-c) with the front strap on the opposite side.
3.
Next attach the back right strap, “B” in Fig. 1. The strap attaches as follows:
a.
Align the strap so the Handlebar Console is pulled tight. Route the strap underneath the
handlebar and between the brake cable housing and handlebar (if equipped with hand brake).
It is critical that the strap not wrap around the brake cable housing.
Wrapping the strap around the brake cable housing can interfere with the proper function of
the brake causing loss of control and injury.
PHOTO B (BLACK) Handlebar Release Lever
HANDLEBAR CONSOLE
INSTRUCTIONS
BOB Trailers, Inc. (800) 893-2447 www.bobgear.com
Ph: (208) 375-5171 Fax: (208) 375-5172 Mail: 5475 Gage St. Boise, ID 83706
Fig 2 Velcro Strap Routing
Fig 1 Console Orientation
RIGHT Side
LEFT Side
If your stroller has
BLACK
handlebar Release Levers as shown
below: Follow steps 1 through 3.
B
A
PHOTO A (RED) Handlebar Release Lever
A-1 Console Installed
B-1 Console Installed
RED Lever
BLACK Lever
Velcro Strap
Routed Above
Black Rod
RED Handlebar Lever
Black Rod
