C
N
L'
L
N
L'
L
N
L'
L
70
98
21
44
98
3.Puttingintooperation/Settings
Factory settings
The PD4-M-1C-GH is preset with time setting 5 min. and twilight switch
1000 Lux.
Attention:
Changes to the settings can only be made by remote control IR-PD4-GH.
Installation and Operating Instruction for
B.E.G.
-Occupancy detectors PD4-M-1C/-S-GH-SM
2a.InstallationoftheLUXOMAT
®
PD4-M-1C-GH-SM
4.PD4-M-1C-GH:Settingscarriedoutusingremote
control(optional)
Remote control LUXOMAT
®
IR-PD4-GH
1. Check Battery:
Open battery compartment by pressing the plastic
springs together and removing the battery-holder.
1.Mountingpreparations
Work on the 230 V mains supply
may only be carried out by qualified
professionals or by instructed persons
under the direction and supervision of
qualified skilled electrical personnel in
accordance with electrical regulations.
Disconnect supply before installing!
The device is not suited for safe dis-
connection of the mains supply.
When in Master/Slave mode of
operation, the Master-appliance must
always be installed at the location
where there is least daylight.
Option:
Wallbracketforremotecontrol
IR-PD4-GH
2c.Selftestcycle
IR-PD4-GH
IR-PD-Mini
B.E.G.
LUXOMAT
®
PD4-M-1C/-S-GH-SM
The detector must be in stalled on a solid and
level surface. The circular cover ring must be removed
prior to assembly. To do this, twist the lens (C) anti-
clockwise through approximately 5° and lift off.
Having connected up the wires in accordance with
regulations, secure the detector with 2 screws.
After installation replace the lens and lock (turn clock-
wise). Mains to be connected.
ATTENTION:
Install the unit in such a manner that
both markings on the housing are positioned in the
longitudinal axis of the area to be monitored (e.g.
high-bay corridors)
5.PD4-M-1C-GH-SM-Dimensions
2b.Rangeindependencefromthemountingheight
Mounting
height
Range (circular detection) T=17°C
Walking across
2.00 m
r = 7.50 m
Ø
= 15.00 m
2.50 m
r = 9.00 m
Ø
= 18.00 m
3.00 m
r = 11.00 m
Ø
= 22.00 m
3.50 m
r = 13.00 m
Ø
= 26.00 m
4.00 m
r = 15.00 m
Ø
= 30.00 m
4.50 m
r = 17.00 m
Ø
= 34.00 m
5.00 m
r = 18.50 m
Ø
= 37.00 m
6.00 m
r = 18.50 m
Ø
= 37.00 m
7.00 m
r = 18.50 m
Ø
= 37.00 m
8.00 m
r = 22.00 m
Ø
= 44.00 m
9.00 m
r = 22.00 m
Ø
= 44.00 m
10.00 m
r = 22.00 m
Ø
= 44.00 m
r=radius / Ø=diameter
close
open
GB
The product enters an initial 60-second
self-test cycle, when the supply is first
connected. The occupancy detector is
ready for operation.
During the selftest cycle, the following
settings can be made:
Light stop active:
(A)
Light off active:
(B)
(see point 7)
Unlocking device
or
or
or
or
Lock device
Settings for relay
Channel 1:
��
�������
���
��
���
��
���
Settings for master with remote control
Reset when
open:
Deletes
all values set
with the remote
control, loads
the default
settings
HA
OFF
Adjust the target value
for brightness
+
+
Target value for brightness
Automatic reading in of the current light value
as a new target light value
Sun button - specified twilight value
Daytime operation
Lag time
Pulse function, fully automatic mode active
Switch between fully automatic/semi-automatic mode
Semi-automatic mode active: Red + green LEDs flash 3x every
5 seconds
Adjust the target value for brightness
to reach the calculated target value, increase the light value by
approx. 50 lux each time the button is pressed
Test mode when closed:
exited automatically after 3 minutes
Test mode when open:
not exited automatically
To deactivate:
press reset
Reset when closed
The lighting relay is switched off, i.e. opened and the lag times
are reset.
Light on/off when closed
(A)
The light remains on/off until movements are detected in
the detection area. After the last detected movement, the light
remains off for the duration of the set lag time.
(B)
If the “Light
stop” function was activated in the selftest cycle, the light is
switched off for 5 seconds (red and green LEDs flash). The device
then returns automatically to the selected operating mode (fully or
semi-automatic mode).
��
���
����
���
Explanation of button functions
��
���
��
���
HA
ON
HA
OFF
9s
2s
LED ON
LED OFF
Pulse spacing PD-Slave
2 or 9 seconds can be set for the pause between
2 pulses sent to the master. The setting can be made
with activated ( ) or deactivated ( ) LED indicator.
For devices with a separate slave input, 2 sec. can be
set.
