3. Putting into operation / Settings
Self test cycle
The product enters an initial 60-second self-test cycle, when
the supply is first connected. The occupancy detector is ready
for operation.
Follow-up time for light control
The time can be set infinitely variably at between
15 seconds and 16 minutes.
Symbol : Impulse < 1sec.
Symbol
TEST
: Test mode (Every movement switches on the
light for a period of 1 second, switching it off for a period of
2 seconds after that regardless of the level of brightness.)
Twilight-switch for light control (relay 1)
The switch-on value for the light can be set at between 10
and 2000 Lux. Using the rotary control, the luminance set
points can be set as desired.
Symbol :
Night-time operation
Symbol : Daytime/Night-time operation
Follow-up time for appliance-control
The time can be set infinitely variably at between 5 minutes
and 120 minutes. There is a period of delay prior to switch-on
of between 5 - 10 minutes for times set in excess of 15 minutes.
Symbol
:
Impulse = 1sec.
Symbol
A
:
Alarm impulse = 1sec.
Installation and Operating Instruction for
B.E.G.
- Occupancy detectors PD1-M-2C/-S-SM/-FC/-FM
2a. Installation of the LUXOMAT
®
PD1-M-2C/-S-SM
2b. Installation of the LUXOMAT
®
PD1-M-2C/-S-FC
4. PD1-M-2C: Settings carried out using remote control (optional)
Remote control LUXOMAT
®
IR-PD
1. Check Battery:
open battery compartment by pressing the plastic
springs together and removing the battery-holder.
2. IMPORTANT
Please pay attention, that the setting is Potentio-
meter 1 at “TEST” and Potentiometer 2
not
at
“SUN”. All values which have been programmed
using the remote control will be deleted in the
event of power failure in the position “TEST/
SUN”. Please switch Potentiometer 2 over to
“MOON” or any other value.
Caution:
Settings with remote control supersede the settings
by courtesy of potentiometers.
1. Mounting preparations
Work on the 230 V mains supply
may only be carried out by quali-
fied professionals or by instructed
persons under the direction and
supervision of qualified skilled elec-
trical personnel in accordance with
electrotechnical regulations.
Disconnect supply before installing!
When in Master/Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.
Lock device
Test mode
Reset to deactivate
Resetting when closed
The lighting relay is switched off, i.e.
opened and the follow-up times reset.
Permanent protection against sabotage
This function blocks the unit permanently (green LED is
illuminated). This operating mode can only be activated
during the period of 5 seconds after pressing the “lock“
button. This status will only permit actuating the function
“Light on/Light off”.
The procedure for leaving this mode is as follows:
1. Switch off the current
2. Apply current for 31 – 59 seconds
3. Switch of the current again
4. Apply current
5. Open detector
Light on/off
The light will remain switched on/off for as long as move-
ments are detected in the areas of coverage. Once the last
movement has been detected, the light will remain on for
the duration of the follow-up time as per setting.
The appliance will then return independently to the mode
selected (Fully or Semi-automatic).
Option:
Wall bracket for remote
control IR-PD
2c. Installation of the LUXOMAT
®
PD1-M-2C/-S-FM
IR-PD
IR-PD-Mini
B.E.G.
LUXOMAT
®
PD1-M-2C/PD1-S
The detector can
be installed in
conventional inlet-
sockets mounted
on the ceiling.
The assembly
plate enclosed
must be stripped
off prior to instal-
lation and secured
to the ceiling
using 4 screws
and ensuring that
it is not laterally
transposed.
For surface-mounting, an inwall sensor unit is combined with a surface-mounted
receptacle as a housing base.
Before mounting the base, the enclosed mounting plate must be mounted true to
side, i.e. the writing must be legible.
Now fix the base on ceiling or wall, but first put the cable through one of the
cable openings provided. The detector must be mounted on a flat, solid surface.
Next prepare the sensor part by screwing in both fixing screws, then connect the
cable as per the wiring diagram.
Now insert the sensor part and check for matching positioning
of the two markings.
Press beyond the spring housing pressure so that the sensor
part firmly locks in place.
Now turn the sensor part counter-clockwise for about 10° to
the stop.
The detector has
been designed and
developed specifically
for installation in sus-
pended ceilings.
A circular opening of
diameter 68 – 70 mm
must be produced in
the ceiling.
Having connected up the cables in accor dance
with regulations, the detector is inserted into
the opening as shown in the drawing opposite
and fixed into position with the assistance of the
spring clips.
120 6050
40
30
15
10
A
16 10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
1
1
2
2
120 6050
40
30
15
10
A
16 10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
2000
1200
600
200
40
max
50
Lux
1500
Lux
ON
OFF
120 6050
40
30
15
10
A
16 10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
120 6050
40
30
15
10
A
16 10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
120 6050
40
30
15
10
A
16 10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
120 6050
40
30
15
10
A
16 10
5
2
1
30
15
TEST
2000
1200
600
200
40
5
B.I.T
.
Q.C
.
PA
SSED
1
GB
6 mm
Having connected up the cables in ac-
cordance with regulations, the detector
can be placed in position as shown in
the drawing opposite and, applying
a little pressure, can then be locked
into position with the assistance of the
spring clips.
Unlocking device
Lock device
Luminance set point
Automatic reading in the current light value
as new luminance set point
Individual light value 2 - 2500 Lux
Follow-up time (relay and channel 1)
15 sec. up to 30 min.
Impulse function (relay and channel 1)
1sec. ON, 9 sec. OFF
Time setting (relay and channel 2)
5 min. up to 120 min.
Impulse function (relay and channel 2)
The voltage-free contact is closed for a period of 2 seconds.
This is followed by a period of idle time of 8 seconds’ duration.
Alarm impulse program for appliance control (relay 2)
The relay will not close until at least three movements have been
registered over a period of 10 seconds (impulse = 1 second).
Preset/user mode
Fully automatic/semi automatic mode => (see page 2, point 5)
Semi automatic: red LED (flashing),
Fully automatic: red LED on for approx. 3 sec.
Resetting when open
All values which have been programmed using the remote
control IR-PD are deleted, and those values which have
been set by potentiometer are activated.
��
���
A
3
max
50
Lux
1500
Lux
ON
OFF
max
50
Lux
1500
Lux
ON
OFF
����
���
��
��� ��
���
R1
�
������
���
R2
