B-band A1 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 28

background image

14

15

8.2

A3.2, A4.2, A5, A6

8.5.

If you are installing an A2 with the optional B-Band AG-MIC

condenser microphone, install the mic at this point. There are a variety
of possible locations, depending on your own taste and preferences.
The two most used places are:

• Connect the mic near the intersection of the X-braces at the top and
position the mic so that it points towards the soundhole at the strings.
This will give a bright sound but may be more sensitive to feedback.

• Connect the mic to a back brace and point the microphone so that
it points to the top of the guitar behind the saddle. In this position
the sound is warm and less sensitive to feedback.

After attaching the mic, it is possible to adjust its direction in a wide
range, simply by bending the metal wire. Bend it carefully to avoid
making a sharp bend, as the paint could come loose. It will require
some experimenting to find the optimal location for your particular
guitar. Be patient and you’ll get a great sound.

Attach the mic cable to the inside of guitar using the two supplied
cable clamps. If needed, roll extra cable as a “coil” in one of the
cable clamps.

8.2

A3.2, A4.2, A5, A6

8.5

«
...
13
14
15
16
17
...
»

Содержание A1





























Отзывы:

Нет отзывов

Похожие инструкции для A1

Бренд: S&P Страницы: 4

Бренд: Yaesu Страницы: 120

Бренд: Datavideo Страницы: 16

Бренд: Simrad Страницы: 52

Efector 800 VTV122

Бренд: IFM Electronic Страницы: 5

Бренд: V2 Страницы: 20

Бренд: LotusRC Страницы: 2

Бренд: Vertex Страницы: 32

Бренд: ZIEHL-ABEGG Страницы: 12

DS-PM1-I16O2-WA

Бренд: HIKVISION Страницы: 2

PULSAR RADAR R86

Бренд: Magnetrol Страницы: 16

Бренд: Icop Страницы: 7

Бренд: Kanga Products Страницы: 26

Бренд: Ecolink Страницы: 2

DTC 2-420-24U-FL

Бренд: NK TECHNOLOGIES Страницы: 2

Бренд: Kenwood Страницы: 18

Бренд: Kenwood Страницы: 51

Бренд: Kenwood Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды