background image

!

!

PG. 6  THE ANSWER

Engine Oil Capacity

FH381V 1.5 L (1.6 US qt.) when oil filter is not removed

FH500V 1.7 L (1.8 US qt.) when oil filter is removed

FH541V 1.7 L (1.8 US qt.) when oil filter is removed

Oil Change

Change  oil  after 

first  8  hours  of  operation

.

Thereafter change oil 

every 50 hours

.

•  Run the engine to warm oil.
•  Be sure the engine (equipment) is level.
•  Stop the engine.
• Open the oil drain valve and drain the oil into
suitable container while engine is warm.

WARNING!

Hot engine oil can cause severe burns. Allow
engine temperature to drop from hot to warm
level before draining and handling oil.

Oil Drain Plug

• Close the oil drain valve.
• Remove oil gauge and refill with fresh oil
(See “Recommended Oils” on p5).
• Check the oil level (see “Preparation” on p3
for oil level check).

Oil Filter Change

• Change the oil filter 

every 100 hours

of

operation.

WARNING!

Hot engine oil can cause severe burns.
Allow engine temperature to drop from hot
to warm level before attempting to remove
oil filter.

Before removing the oil filter, place a
suitable pan under filter connection.

• Drain engine oil into a suitable container.

• Rotate the oil filter (A) counterclockwise to
remove it.

• Coat a film of clean engine oil on seal of new
filter.

• Install new filter rotating it clockwise until
seal contacts mounting surface (B). Then
rotate filter 3/4 turn more by hand.

• Supply engine oil as specified.

• Run the engine for about 3 minutes, stop
engine, and check oil leakage around the filter.

• Add oil to compensate for oil level drop due to
oil filter capacity (See “Oil Level Check” on p3).

WARNING!

Engine oil is a toxic substance. Dispose 
of used oil properly. Contact your local
authorities for approved disposal methods
or possible recycling.

!

KAWASAKI ENGINE BATTERY START WIRING DIAGRAM

THE ANSWER PG. 11

PARTS LIST FOR BUFFER FUEL SYSTEM

PART #

DESCRIPTION

PART #

QTY

1

QUICK COUPLER

152-700

1

2

LPG HOSE 14" 

267-P5561-14

1

LPG HOSE 20"

267-P5561-0410

1

3

FUEL LOK-OUT (VACUUM)

152-300

1

4

90˚ FITTING

177-116B04

1

5

VACUUM HOSE FITTING

166-62029

1

6

1 1/2" NIPPLE

177-56021

1

8

FUEL HOSE FITTING

166-62039

1

9

FUEL LOK-OUT (12 VOLT)

152-N3-0173-1

1

10

FUEL REGULATOR (T60-E)

152-500

1

CAUTION!

!

Содержание answer

















Отзывы: