Azbil ALTJ 9000 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 68

Azbil ALTJ 9000 Series Скачать руководство пользователя страница 29

7-1

Chapter 7 Operation

WARNING

Install this product in a location where the operating conditions (pressure rating, temperature,
humidity, voltage (

specification sheet), mounting orientation, and ambient atmosphere (

Chapter 3 Installation) are satisfied. Failure to do so may cause a fire or malfunction.

CAUTION

Do not perform the SFN communication when the process of the liquid level transmitter is in the
automatic control status. Doing so may cause the output to vary, resulting in a hazardous operation
status.

This chapter describes the following matters.

y

Connecting a communicator (CommStaff, etc.) to this device

y

Checking the settings of the transmitter

y

Preparations before measurement

y

Starting and stopping measurement

For details about how to operate CommStaff, refer to the relevant user's manual below.

y

Field Communication Software CommStaff Model: CFS100 (Common Edition) User's Manual,
No. CM2-CFS100-2001

y

Field Communication Software CommStaff Model: CFS100 Instruction Manual (Smart ALTJ

™

9000

Immersion-type Liquid-Level Device Edition), No. CM2-CFS100-2014

Note Be sure to read the user's manual thoroughly before connecting to the transmitter.

«
...
27
28
29
30
31
...
»

Содержание ALTJ 9000 Series





































































Отзывы:

Нет отзывов