Ayce 7613164565631, Оригинальное руководство пользователя, Страница: 35 / 40

68 | 69
GB
Screw the other 2 brackets with the smaller screws below the heater, in the relevant
holes (Fig.3): screw through the long side of the bracket, the short side facing down.
The short side will come to lie against the wall.
Hang the heater on both brackets and let it drop into the channels.
The short sides of the other 2 brackets will fall against the wall. Mark where these
must be screwed to the wall and lift the heater out of the brackets.
Drill 2 holes at the marked locations and insert plugs.
Hang the heater back on the brackets, let it drop into the channels and screw the last 2
large screws through the lower brackets against the wall.
Check to ensure your heater is horizontal and secure, with the minimum distance to
the floor, ceiling and any side walls.
Turn the heater upside down. Place a blanket (or something similar) under the heater
to prevent damage!
Place the feet on their place on the bottom of the heater. This will ensure that the
threaded holes will align correctly.
Securely attach the feet to the heater using the (2x2) self-tapping screws.
Return the heater to the upright position.
Make sure a working heater is always placed on a solid, flat and horizontal surface.
Deep-pile carpeting is unsuitable!
Check to make sure the main switch is set to position“0” (off).
Check that the heater is stable and upright, in line with instructions.
Now insert the plug into the 230V socket.
Set the main switch to position “I” (on). The display will show: OFF
Press the ON/OFF button in order to switch the heater on. The display lights up and
the heater can be operated.
Now, set the day and time. Press and hold SET until SET appears on the screen. The
numbers of the weekdays (line 4) will blink. Use the + and – buttons to find the right
day (1 – Monday, 2 = Tuesday, etc.) and confirm with SET. The hour will now blink. Use
the + and – buttons to set the right hour and confirm with SET. The minutes will now
blink. Use the + and – buttons to set the right minutes and confirm with SET. The day
and time are now set.
The day and time settings will be lost if the heater is switched off using the main
switch or plug; these will be retained if the ON/OFF button is used.
If you do not set a time and day, the heater will assume that it is day 1 and 00.00.
The screen goes off automatically after 2 minutes and can be turned on again with any
button.
Press MOD to set whether you wish to work with the M or P function.
Under the M-function, you use the + and – buttons (remote control: with the bar
button) to set the capacity at which the heater will work: low, medium or high - see
technical details. The thermostat cannot be adjusted.
Under the P-function, you can use the + and – buttons to set the desired temperature
for the heater, which it will then try to maintain. The heater will automatically select
the correct capacity: 1 or 2 degrees of heat = low, 3, 4 or 5 degrees of heat is medium
and 6 or more degrees of heat is high. Once the desired temperature is reached, the
heater automatically turns off, and then back on again when it cools down.
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Fig. 2
Fig. 4
Fig. 3
Freestanding
Attach the feet supplied to the underside of the heater (Fig.4):
Warning! Ensure that there is sufficient distance from the wall, fixtures or other
appliances. The distance must be at least 1 m to exclude the risk of fire.
Using the operation panel
The operating panel (3) has 6 buttons: MOD / SET / WEEK / + / - / and the ON/OFF button
Please Note:
USING FOR FIRST TIME AND OPERATION
Note!
Since the appliance and its heating elements are slightly greased when delivered,
there might be a slight development of smoke and odor the first time it is used.
This is harmless and stops after a short a while. Be sure to provide for sufficient
ventilation during such time.
!
MIN.150CM
MIN.30CM
MIN.30CM MIN.30CM