background image

6

STEERING WHEEL CONTROL SETTINGS 

(CONT)

Continued on the next page

Radio legend

1. Eclipse (Type 1)
2. Kenwood
3. Clarion (Type 1)
4. Sony/Dual
5. JVC
6. Pioneer/Jensen

7. Alpine
8. Visteon
9. Valor
10. Clarion (Type 2)
11. Metra OE
12. Eclipse (Type 2)

13. LG
14. Parrot
15. XITE
16. Philips
17. TBD
18. JBL

Remapping the steering wheel control buttons

Let’s say you have AXDIS-GMLN30 initialized and you want to change the button assignment 
for the steering wheel control buttons. For example, you would like Seek-Up to become 
Mute. Follow the steps below to remap the steering wheel control buttons:

1.

  Ensure the AXDIS-GMLN30 is visible so you can see the L.E.D. flashes to confirm button 

recognition.

 

Tip:

  

Turning the radio off is recommended.

2.

  Within the first twenty seconds of turning the ignition on, press and hold the Volume-Up 

button on the steering wheel until the L.E.D. goes solid.

3.

  Release the Volume-Up button, the L.E.D. will then go out; The Volume-Up button has now 

been programmed.

4.

  Follow the list in the Button Assignment Legend to reference the order in which the steering 

wheel control buttons need to be programmed.

 

Note:

 

If the next function on the list is not on the steering wheel, press the Volume-Up 

button for (1) second until the L.E.D. comes on, and then release the Volume-Up button. This 

will tell the AXDIS-GMLN30 that this function is not available and it will move on to the next 

function.

5.

  To complete the remapping process, press and hold the Volume-Up button on the steering 

wheel until the L.E.D. in the AXDIS-GMLN30 goes out.

1. Volume-Up
2. Volume-Down
3. Seek-Up/Next
4. Seek-Down/Prev
5. Source/Mode
6. Mute
7. Preset-Up
8. Preset-Down
9. Power

10. Band
11. Play/Enter
12. PTT (Push to Talk) * 
13. On-Hook *
14. Off-Hook *
15. Fan-Up *
16. Fan-Down *
17. Temp-Up *
18. Temp-Down *

Button assignment legend

Note:

 

Not all radios will have all of these commands. Please refer to the manual provided with the 

radio, or contact the radio manufacturer for specific commands recognized by that particular radio.

Not applicable in this application

Содержание AXDIS-GMLN30









Отзывы: