Axor Massaud, Инструкция по эксплуатации, Страница: 4 / 52

0 4
A S S E M B L Y (see page 32)
S P A R E P A R T S (see page 47)
C L E A N I N G (see page 46)
M A I N T E N A N C E (see page 46)
O P E R A T I O N (see page 45)
D I M E N S I O N S (see page 31)
Do not use silicone containing acetic acid!
If silicone containing acedic acid is used, the components of the products will
be damaged. We recommend fungus-resistant sanitary silicone for filling the
gaps between the elements. After a while, the silicone sealant may become
discoloured. Silicone gaps require maintenance and are not covered by
warranty.
S Y M B O L D E S C R I P T I O N S A F E T Y N O T E S
Gloves should be worn during installation to prevent crushing and cutting injuries.
Children as well as adults with physical, mental and⁄or sensoric impairments must
not use this product without proper supervision. Persons under the influence of
alcohol or drugs are prohibited from using this product.
The product may only be used for bathing, hygienic and body cleaning purposes.
The bath water temperature may not exceed 40ºC.
Do not use electrical devices, such as hair dryers, radios, etc. near or inside the
tub.
The tub must be emptied after every bath.
The product's design must not be altered. Only use original spare parts.
In order to prevent the tub from tipping over, it must be secured.
In order to enter the tub properly, follow the visual instructions on page 45 and
enter and exit the tub along the longer straight side.
If the tub is to be used in public areas, the included anti-slip stickers must be used.
I N S T A L L A T I O N I N S T R U C T I O N S
⁄ Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
⁄ The plumbing codes applicable in the respective countries must be observed.
⁄ The tub must not be installed outdoors.
⁄ The door width of the installation site must be taken into consideration. The
dimensions can be taken from the technical specifications.
⁄ The tub must be installed on a floor that is suited for high-moisture rooms.
⁄ The required minimum floor load is 550 kg⁄m². The floor must be levelled properly,
i.e. it must be horizontal and even.
⁄ The tub must be installed so that the safety areas are ensured as per E
IEC 60364-7-701 ⁄ DIN VDE 0100 T 701.
⁄ Because of its design, the tub must have its drain in the floor area. There is no
possible drain connection in the wall.
⁄ The drain connection must be made as per the currently valid DIN
1986⁄EN12056 and the local regulations.
⁄ Only suitable fastening material may be used! The enclosed screws and plugs are
only suitable for concrete. With different floor structures, the dowel manufacturer's
instructions must be observed.
⁄ The tub can be affixed to the floor using two-component adhesive (see page 39).In
this case, the installation and processing instructions of the adhesive manufacturer
must be observed.
⁄ If the tub is sealed toward the floor, one of three inspection openings may not be
closed up to be able to detect water leaks.
⁄ After installing the tub, the installer must perform a leak test on the tub.
⁄ The installer must confirm the proper transfer of the installed tub on the respective
page of the installation instructions.
EN
S P E C I A L A C C E S S O R I E S (order as an extra)
Lacquer pen Alpine White L 090 B01 (Audi ⁄ VW) for touching up minor paint
damage
The tub was installed properly as indicated by the installation instructions by
Hansgrohe SE as well as per the respective DIN ⁄ EN standard. The tub was also
inspected for leaks and proper installation.
Date Company ⁄ Stamp ⁄ Signature
W A R N I N G O F S L I P P E R Y S U R F A C E S .