manualshive.com logo in svg

Axminster Craft AC456SS, Инструкция по эксплуатации

Поделиться
Скачать
Axminster Craft AC456SS Скачать руководство пользователя страница 23

Maintenance

23

Rocker Arm Bearing Bushes

After a period of use it is recommended to lightly oil the upper 
and lower rocker arm bearings, see fig 43-44.

Fig 45-46-47

Bearing bush 

rubber bungs

Bearing bush

Troubleshooting

PROBLEM

PROBABLE CAUSES

SUGGESTED REMEDY

Breaking Blades

1. Incorrect tension.
2. Overworked (worn out) blade.
3. Wrong blade being used.
4. Twisting blade in wood.

1 Adjust blade tension.
2. Reduce feed rate or replace blade.
3.  Use narrow blades for thin wood, 

wider blades for thicker wood.

4. Avoid side pressure on blade.

Motor will Not Run

1. Defective cord,plug or outlet
2. Defective motor.

1. Unplug saw, replace defective parts.
2.  Repairs MUST be made by a qualified 

technician. Call Axminster Tool Centre. 

(Technical Sales Phone: 0800 371822).

Excessive Vibration

(Some vibration is inevitable when 

the saw and motor are running)

1. Improper mounting of saw.
2. Unsuitable mounting surface.
3. Loose table.
4. Motor mount is loose

1. See proper mounting instructions.
2.  Replace plywood workbench 

surface with solid lumber surface.

3.Tighten table clamping knob.
4. Tighten motor mount screws.

Содержание AC456SS





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды