Axis V5914 Скачать руководство пользователя страница 9

Страница: 9 / 64

AXIS V5914 PTZ Network Camera

Hardware Overview

The control button is used for:

•

Resetting the product to factory default settings. See

page 54

•

Connecting to an AXIS Video Hosting System service. See

page 46

. To connect, press and hold the button for about 3

seconds until the Status LED flashes green.

•

Connecting to AXIS Internet Dynamic DNS Service. See

page 46

. To connect, press and hold the button for about 3 seconds.

LED Indicators

Status LED

Indication

Unlit

Connection and normal operation.

Green

Shows steady green for 10 seconds for normal operation after startup completed.

Amber

Steady during startup. Flashes during firmware upgrade.

Amber/Red

Flashes amber/red if network connection is unavailable or lost.

Red

Flashes red for firmware upgrade failure.

Microphone power LED

Indication

Unlit

Phantom power off.

Blue

Phantom power on.

Note

• The tally LED can be configured to be lit or unlit during normal operation. To configure, go to

Setup > System Options >

Ports & Devices > LED

. See the online help for more information.

• The tally LED only indicates network transmission. If video or audio is only transmitted through HDMI or SDI the tally LED

will be unlit.

Tally LED

Indication

Unlit

Camera idle.

Red

Active network transmission or recording.

Содержание V5914

































































Результаты поиска

Содержание V5914

Отзывы:

Похожие инструкции для V5914

Бренды по названию

Популярные бренды

Axis V5914, Руководство пользователя

Результаты поиска

Содержание V5914

Отзывы:

Похожие инструкции для V5914

Бренды по названию

Популярные бренды