AXIOMTEK VTA-7570T Скачать руководство пользователя страница 28

Страница: 28 / 71

VTA-7570T User

’

s Manual

PHOENIX-AWARD BIOS UTILITY

Security Option

This item allows you to limit access to the system and Setup, or just to
Setup. The default value is

“

Setup

”

System

If a wrong password is entered at the prompt, the system
will not boot, the access to Setup will be denied, either.

Setup

If a wrong password is entered at the prompt, the system
will boot, but the access to Setup will be denied.

NOTE

To disable the security, select PASSWORD

SETTING at Main Menu and then you will be
asked to enter a password. Do not type anything,
just press <Enter> and it will disable the security.
Once the security is disabled, the system will
boot and you can enter Setup freely.

Small Logo(EPA) Show

If enabled, the EPA logo will appear during system booting up; if disabled,
the EPA logo will not appear.

Press <Esc> to return to the Main Menu page.

Содержание VTA-7570T








































































Результаты поиска

Содержание VTA-7570T

Отзывы:

Похожие инструкции для VTA-7570T

Бренды по названию

Популярные бренды

AXIOMTEK VTA-7570T, Руководство пользователя

Результаты поиска

Содержание VTA-7570T

Отзывы:

Похожие инструкции для VTA-7570T

Бренды по названию

Популярные бренды