AXIOMTEK VTA-7570T Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 71

background image

VTA-7570T User

’

s Manual

Hardware Installation

11

VTA-7570T 10/100 Base-T Hub into the standard RJ-45 connector.
The pin assignment of the RJ-45 is listed below;

Pin

Signal

1

TX+ (Data transmission positive

2

TX- (Data transmission negative)

3

Rx+(Data reception positive)

4

RJ45 termination

5

RJ45 termination

6

Rx- (Data reception negative)

7

RJ45 termination

8

RJ45 termination

2.5 Mounting Way : Panel mount

The VTA-7570T is designed for panel mount application. To mount the
VTA-7570T, the standard set of mounting kit (included in the system
packaging) is needed.

1 2 3 4 5 6 7 8

RJ-45

«
...
17
18
19
20
21
...
»

Содержание VTA-7570T








































































Отзывы:

Нет отзывов

Похожие инструкции для VTA-7570T

Бренд: Canon Страницы: 160

Бренд: SeaLevel Страницы: 40

ECS-9671 GTX950

Бренд: Vecow Страницы: 111

QDSP-0200 Series

Бренд: Quanmax Страницы: 39

Бренд: VisuNet Страницы: 81

Hummingbird Lite

Бренд: Amico Страницы: 24

OptiPlex 7080 Micro

Бренд: Dell Страницы: 57

Бренд: Dell Страницы: 147

Бренд: Aplex Страницы: 69

Бренд: BAC Страницы: 22

Бренд: Pioneer Страницы: 124

Бренд: Yamaha Страницы: 65

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 420

Бренд: Moxa Technologies Страницы: 53

Бренд: Cybernet Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды