AXIOMTEK MPC152-832 Скачать руководство пользователя страница 43

Страница: 43 / 50

MPC152-832

User’s Manual

AMI BIOS Setup Utility

3.6

Boot Menu

The Boot menu allows users to change boot options of the system.



Boot Settings Configuration

Setup Prompt Timeout

Use this item to set number of seconds to wait for setup activation key.

Bootup NumLock State

Use this item to select the power-on state for the NumLock.. The optional settings are: [On];
[Off].

GateA20 Active

If Upon Request is selected, GA20 can be disabled using BIOS services. If Always is selected,
disabling G20 is not allowed; this option is useful when any RT code is executed above 1MB.

Option ROM Messages

Set display mode for option ROM. Configuration options are Force BIOS and Keep Current.

Interrupt 19 Capture

If this item is enabled, this function makes the option ROM to trap Interrupt 19.

Boot Option Priorities

These are settings for boot priority. Specify the boot device priority sequence from the
available devices.

Содержание MPC152-832



















































Результаты поиска

Содержание MPC152-832

Отзывы:

Похожие инструкции для MPC152-832

Бренды по названию

Популярные бренды

AXIOMTEK MPC152-832, Руководство пользователя

Результаты поиска

Содержание MPC152-832

Отзывы:

Похожие инструкции для MPC152-832

Бренды по названию

Популярные бренды