Basic connection
Ü
It is recommended to be connected to a multi-system TV.
Ensure that this player and other equipment to be
connected to the unit are in the standby or off mode and
disconnect the AC power cords before commencing
connection.
Do not block ventilation holes of any piece of the equipment
and arrange them so that air can circulate freely.
Read through the instructions before connecting other
equipment.
Ensure that you observe the color coding when connecting
audio, video cables.
During DVD play, the TV volume may be at a lower level
than during TV broadcasts, etc. If this is the case, adjust
the volume to the desired level.
If the DVD/CD player is connected to the TV through a
video cassette recorder, the picture may not be played back
normally with some DVDs. If this is the case, do not
connect the player via the VCR.
Note:
The mains plug is used as disconnect device, the
disconnect device shall remain readily operable.
To power outlet
AC power cord
To video input connector (yellow)
To audio input connectors (red, white)
Video/audio cable
2
L
R
OPERATIONS
PREPARATION
GET STARTED
ADJUST THE VOLUME
SKIP AHEAD OR BACK
Power on the TV set and select video input mode.
1. Insert the AC cord to the AC socket of player, and plug the
other end to an applicable wall outlet. slide the FUNCTION
switch to the DVD/USB/CARD position.
2. Open the disc tray.
3. Place a disc onto the disc tray.
4. Close the disc tray and the playback starts automatically.
5. When a menu screen appears on the TV, move the navigation
buttons or press the numeric buttons to select a preferred
track number, then press OK button to start playback.
Adjust the volume to your favorite by rotating the volume
control.
Press NEXT or PREVIOUS button on the remote or SKIP
DOWN/PREVIOUS BUTTON &SKIP UP/NEXT BUTTON once
during play to skip a chapter(DVD) or a track (CD) ahead or
backwards.
RAPID ADVANCE/REVERSE
STOP PLAYBACK
SLOW-MOTION PLAY (DVD)
SEARCH FOR PREFERRED SCENE
PROGRAM PLAY(UP TO 16 MEMORIES)
ON SCREEN DISPLAY INFORMATION
During playback, press and hold F.FWD button or F. BWD
button several times to scan the disc forward or backward at
X2, X4, X8, X20 normal speed.
Press PLAY button to resume normal play.
Press STOP button during playback to stop playback; the
player activates its resume function when STOP is pressed in
STOP mode; press PLAY button again, playback resumes at
the point it stopped previously; open the disc tray or press the
STOP button one more time to clear the resume function.
Press and hold ZOOM/SLOW button on the remote control
during playback, the disc will be played at 1/ 2 normal speed
at first, each time this button is pressed, the play speed
becomes slower (down to 1/7 normal speed.)
Press PLAY/PAUSE button, normal play will resume.
Press REPEAT button during play, it will repeat play one
chapter/title or repeat all (for DVD disc), or repeat play a track
or all tracks (CD), or repeat the specified points (A-B).
1. Press SEARCH button during play and highlight the item to
be played (Title, Chapter, or Chapter time)by navigation
buttons.
2. Input the desired number or time via the numeric buttons.
3. Press OK Button to confirm and the playback from the
located scene starts.
4. To exit search menu, press SEARCH button directly.
1. Press PROGRAM during playback to display the program
menu.
2. Select location(s) to be memorized via navigation buttons
and then enter desired Titles/Chapters numbers via
numeric buttons.
: Inputting leading zero is not necessary. If the
chapter/title/track number is behind the cardinal 10, press
the unit digital key first and then another unit digit. Some
figure inputs may be useless, because it 's greater figure
than total title/chapter/track number on the disc.
Example: Track 3, press "3"
Track 12, press "1" and then "2"
Track 21, press "2" and then "1"
3. To start programmed playback, select PLAY on the menu, and
then press OK Button on the remote control.
pressing PROGRAM button again to exit programming.
4. To clear all items, select the <CLEAR> on the menu, and then
press OK button on remote control.
5. To change programmed items, scroll the Navigation button to
the item to be changed and enter the desired track number on
the screen, the selected item will be changed.
6. You can also cancel program mode by clearing all the items in
the program menu.
When the player is in operation, press DISPLAY button
continuously on the remote control, the screen will display parts
of information(current disc type, title number, chapter number,
playtime, audio language, audio type, subtitle language and
multi angle, etc) in a sequence.
REPEAT
Note
ZOOM PLAY
Press the ZOOM/SLOW key continuously to zoom in the picture
by 2, 3, and 4 times, zoom out by 1/2, 1/3, 1/4 normal size.
Press this key once more when the picture is at 1/4 size to return
to the normal size display.
Scroll to view the enlarged picture using Navigation buttons.
