background image

Charger 6 / Charger 12  

  rel. 1.3c   -E-   english, page  

16

 of 

22

  

4.5 

Operation state signaling 

The power supply is equipped with LED, sound and remote indication systems. The LED indication is 
used in order to bring attention of the personnel to the operation state of the device and to inform 
about the reason of a potential malfunction. The sound indication system is activated together with 
the lighting signalling. 
Fault indication is maintained as active until it is deactivated using the vertical arrow button located in 
the display panel. Short press of the button switches the sound indication system off, while keeping 
the LED and remote indication systems active. The remaining indication systems can be deactivated 
by pressing and holding the vertical arrow button for over 5 seconds. However, the use of the key is 
effective only when the reason triggering the event generation is no longer present. The indication 
systems are reset automatically only when the network power supply is restored and external signals 
at the 

EXT. FAULT 1

 and 

EXT. FAULT 2

 inputs are no longer detected. In the case of the power failure, 

instead of a continuous sound signal, a short, intermittent signal is generated every 15 seconds. 
The LED indication system comprises four LED diodes located in the front panel of the power supply. 
Three diodes represent the current operation mode (

MAINS

 - green, 

BATTERY 

- yellow, 

CHARGING

 - 

green), and the fourth - fault (

FAULT

 - yellow).  

The remote indication system includes three sockets denoted MAINS FAULT, BATTERY FAULT and 
GENERAL FAULT. Each of the sockets has three plugs, switched between by using relays, completely 
separated from all other circuits. During normal, correct operation of the power supply unit, relay 
coils are active. It means that Mains Fault (power failure) indication, Battery Fault and General Fault 
indications are executed by switching the appropriate relay off (current loss in the relay coil). 
The contact setting in this state (so called zero-voltage state) has been presented next to each 
corresponding

 socket. 

List of states of the LED and remote indication systems is presented in the tables below. 

LED indication system in the front panel. 

DESCRIPTION 

COLOUR 

STATE 

EVENT DESCRIPTION 

MAINS 

green 

on 

Normal operation state at the mains present. 

off 

No mains or rectifier fault. 

BATTERY 

yellow 

on 

Battery operation (no mains or rectifier fault). 

off 

Normal operation state at the mains present. 

CHARGING 

green 

pulsating 

Bulk charging. 

on 

Charging during floating mode (after the bulk 
charging has finished). 

off 

Charging has finished. 

FAULT 

yellow 

on 

Fault occurred within the power supply unit or 
external fault. Please read the error code from the 
display in order to determine the reason. 

pulsating 

External fault indication at 

EXT. FAULT 1 

or 

EXT. FAULT 

2

 input. 

*).

 

*) If it is sent together with the external fault indication an internal fault occurs, the LED diode 

FAULT

 

 will be on continuously. 

Содержание CHARGER 12























Отзывы: