background image

 

The warranty covers the costs of material and working time, transport costs are to be borne 
by the owner.  
 
Provisions for this warranty are: 
 

 

The unit must have been purchased from an authorised dealer. Equipment from other 
sources will not be repaired, not even at charge. 
 

 

The warranty registration card, together with a copy of the bill of sale, must be received 
by us within four weeks of the date of purchase. 
 

 

The defect must not have been caused by improper handling or misuse. 
 

 

Return the unit to us only in its original packing. If this is not possible we are entitled to 
refuse acceptance. We will not assume responsibility for transport damage under any 
circumstances. 
 

 

A short description of the defect is to be included with the returned unit. 
 

 

In cases of doubt we reserve the right to request a copy of the bill of sale. 
 

 

We also reserve the right to levy a handling charge for items returned without good or 
valid reason, or if the unit proves to be not defective. 

 
 

NOTE: 

If you are returning the unit from a country other than Germany you should ensure that 

correct export documents are obtained. We cannot accept any charges for costs arising from 
improper or incomplete export documentation.

 

 
If you have purchased your unit from a dealer outside Germany please refer to him or the 
relevant importing firm to process the warranty. 
 
 

5

 

Technical Data 

 

MA 6.2 

 

5.1

 

Amplifier 

 
Input impedance Cinch / XLR 

 

 

33 / 66 k

Ω

 

Signal-to-noise-ratio (SNR)   

 

 

101 dB(A) 

Frequeny response   

 

 

 

< 5 Hz - > 100 kHz 

THD (25 W/4 Ohms)   

 

 

 

< 0,01% 

Damping factor 

 

 

 

 

> 500 

Power  

 

 

 

 

 

2 x 335 Watts (4 

Ω

) / 2 x 225 Watts (8 

Ω

 
 
 

5.2

 

Other 

 
Supply voltage 

 

 

 

 

115/230V / 50/60Hz 

Содержание OVATION MA 6.2













Отзывы: