AVIX Autonomic Mark II, Руководство пользователя

Страница: 8 / 16

7
User Manual AVIX Autonomic Mark II - Version 2.0
Cable requirements:
• Outdoor rated
•
Conductor: 1 - 2.5 mm
2
(14 - 17 AWG)
• Cores: 3
•
Outer diameter: 6-15 mm (0.25 – 0.6”)
3.2 Connecting the Autonomic to power
1 Connect the CEE Plug (exiting the Mains Power Adapter) to the CEE
connector. The AVIX Autonomic is now powered and ready to be
configured.
4. Configuration
CAUTION:
• Do not drop. This product may malfunction if subjected to strong
shocks or vibration.
• The AVIX Autonomic is an automated laser device intended for bird
repelling purposes only.
• When using the AVIX Autonomic, always adhere to the safety
precautions outlined in this document.
• To prevent injuries or damage as a result of entrapment, stay clear of
the Motor Platform during operation.
4.1 Power up
CAUTION: Before using the AVIX Autonomic ensure that:
• All bolts connecting the base of the Motor Platform to the supporting
structure are tightly secured.
• The AVIX Autonomic is not allowed to wobble or tilt when
operational. If stability is insufficient, improve supporting structure.
• The AVIX Autonomic should not be subjected to surface vibrations,
as these can lead to a displacement of the laser projection over time.
• All power cables are properly connected.
• The emergency stop button is deactivated.
• The key is positioned inside the key lock switch and is switched to
the ‘active’ position (turn in a clockwise direction).
WARNING: Do not stare into the laser beam during configuration.
CAUTION: After pressing the ( ) button, the Motor Platform
may start moving. Use the ( ) button to switch the AVIX Autonomic
ON/OFF. When powered, the AVIX Autonomic is automatically
switched ON.
3. Assembly
1 Carefully take all parts out of the AVIX Autonomic flight case.
2 Position the Motor Platform on a flat and horizontal surface.
3 Place the Payload on top of the Motor Platform by aligning the four
holes on the top of the Motor Platform with the holes on the sides
of the Payload. Make sure to position the Payload in the correct
orientation, as shown in the Assembly overview on page 2.
CAUTION: Although the Payload may rest on the Motor Platform,
it is not yet connected. Perform the next step carefully so the Payload
will not drop.
4 Use the 4 (four) screws to secure the Payload to the Motor Platform.
Use the Hex Key to tighten the screws.
5 Unscrew the connector protection cap on the back of the Rear Cap.
6 Connect the Payload plug exiting on the side of the Motor Platform
to the connector on the back of the Rear Cap. Make sure to tighten
the screw connection properly to establish a watertight connection.
7 Connect the plug exiting the base of the Motor Platform to the
Power Switch Module. Make sure to tighten the screw connection
properly to establish a watertight connection.
8 Connect the plug exiting the Mains Power Adapter to the remaining
connector on the Power Switch Module. Make sure to tighten the
screw connection properly to establish a watertight connection.
9 Secure the base of the Motor Platform to its supporting structure.
The Power Switch Module is a required module. The Autonomic will
stay in the initialization phase if the Power Switch Module is not
installed.
3.1 Preparing the mains power connection
WARNING: Always make sure that all equipment is de-energized
and disconnected from mains power before working on the mains
power connection.
1 Connect the CEE Connector (mains power side) to the power cable
(cable specifications are shown below). Use a flat blade screwdriver
to open the connector and expose its terminals. Use a Philips screw
driver to secure the cores to the terminals. Make sure the cores are
stripped sufficiently and the screws are secured tightly to ensure
proper conductivity. Close the connector again by combining its
parts until it clicks into place.
2 Power can be restored. Provide a voltage of 100 - 277V to the power
cable. The mains power connection is ready for use.
The power cable is not provided with the AVIX Autonomic.