Avigilon 2.0C-H5A-PTZ-DC36 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 47

background image

Bottom View - LEDs

1.

Connection status LED indicator

Green LED provides information about device operation. For more information, see

Status LED Indicator

.

2.

Link LED indicator

Amber LED indicates if there is an active connection in the Ethernet port.

Note:

The camera LEDs will flash and provide status information when the camera is establishing a

network connection. Once the camera starts streaming video the LEDs will automatically turn off.

Bottom View - LEDs

3

«
...
7
8
9
10
11
...
»

Содержание 2.0C-H5A-PTZ-DC36
















































Отзывы:

Нет отзывов

Похожие инструкции для 2.0C-H5A-PTZ-DC36

Бренд: Minolta Страницы: 41

Бренд: Panasonic Страницы: 2

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 28

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 2

Бренд: Yada Страницы: 20

Бренд: Vacron Страницы: 5

Бренд: Vacron Страницы: 2

Бренд: YesCam Страницы: 58

Бренд: CIS Страницы: 29

Бренд: Targa Страницы: 386

ThermoVisualizer

Бренд: LaserLiner Страницы: 88

Бренд: THOMSON Страницы: 5

Бренд: Lorex Страницы: 2

Бренд: LENCO Страницы: 6

PREMIUM INDOOR CAMERA

Бренд: Frontpoint Страницы: 9

Бренд: Odys Страницы: 66

Бренд: Aluratek Страницы: 1

Бренд: Kodak Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды