Avaya Tenovis Integral-55 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 25

Avaya Tenovis Integral-55 Скачать руководство пользователя страница 25

AVAYA E1/QSIG

25

The above information is provided by AVAYA Inc. as a guide. See disclaimer on page 1

displayed the PBX must send the MAS the Calling Name using
the QSIG Name Identification Supplementary Services Protocol
(ECMA-164).

CHANGE HISTORY

Revision

Issue Date

Reason for Change

Version A

04/09/07

GA release

Version B

06/01/07

Updated Consideration 8.12. Reformatted section 8.0

Version C

03/08

Corrected Consideration 8.12

Version D

05/05/08

Updated to support MM 4.0

Version E

05/16/08

Removed Dialogic Driver release from Section 2.0

Version F

06/11/08

Added sidebar note in Section 5.0 detailing administration of
trunk group and to leave out highest order timeslot/port.

Version G

2/02/09

Updated to support MM 5.0; Limit Requests for MWI
changed in Section 6.0

Version H

02/12/09

Changed screen shot for VMSC and added sidebar in Section 6.0.

Version I

07/09

Updated to support MM 5.1; changed wording in note on sidebar
for VMSC in Section 6.0; Added note regarding collocated
PBX/MM on page 1

Version J

07/20/09

Updated Consideration 8.11 to reflect calling party number/name
display on ringing phone and PBX requirements needed

Version K

01/19/10

Added note indicator to titles of Section 2.0 and 3.1; added
corresponding note in sidebar; removed word “supported” in same
sections for MAS releases and PBX Software releases.

©2010 AVAYA Inc. All rights reserved. All trademarks identified by the ®, SM and TM are registered trademarks,
servicemarks or trademarks respectively. All other trademarks are properties of their respective owners. The above
information is based on knowledge available at the time of publication and is subject to change without notice. Printed in
U.S.A.

AVAYA

Inc.

1033 McCarthy Blvd.
Milpitas, CA 95035
(408) 577- 7000

http://www.avaya.com

«
...
23
24
25

Содержание Tenovis Integral-55


























Отзывы:

Нет отзывов