Avaya Tenovis Integral-55 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 25

Avaya Tenovis Integral-55 Скачать руководство пользователя страница 1

Disclaimer: Configuration Notes are designed to be a general guide reflecting AVAYA Inc. experience configuring its systems. These
notes cannot anticipate every configuration possibility given the inherent variations in all hardware and software products. Please
understand that you may experience a problem not detailed in a Configuration Note. If so, please notify the Technical Assistance Center
at (800) 876-2835, and if appropriate we will include it in our next revision. AVAYA Inc. accepts no responsibility for errors or omissions
contained herein.

Configuration Note 88541

–

Version K (1/10)

AVAYA Tenovis Integral-55

E1

/

QSIG - EMEA

Overview

This Configuration Note is intended for Avaya certified Modular Messaging
technicians/engineers who are familiar with Modular Messaging procedures and
terminology. It also assumes that you are Avaya certified or very familiar with
the features and functionality of the Avaya PBXs supported in this Configuration
Note and the QSIG protocol.

Use this document in conjunction with

Modular Messaging Installation Guide

and

the Avaya PBX

Administration Guide.

Please read the entire document before attempting any configuration.

1.0 METHOD OF INTEGRATION

With E1 QSIG integration, one digital pathway between the Avaya

™

PBX and the

Avaya Message Application Server (MAS) transmits both call information and
voice communications. The pathway is provided by an ISDN digital link (QSIG),
which provides channels that connect to the Dialogic E1 card. Within the D-
Channel, routing information is sent to the MAS containing information regarding
the source of the call with reason codes. The MAS processes call information
from the supplementary code in the D-Channel, which routes call reasons directly
to mailboxes. Message-Waiting indication is set and canceled using the
supplementary code service. Voice is carried through the system in digital format.

A v a y a

™

M o d u l a r M e s s a g i n g

The PBX and MM are

assumed to be collocated.

For other configurations

please consult with the

Switch Integrations group.

With E1 QSIG, one digital

pathway between the PBX and

the Avaya Message Application

Server transmits both call

information and voice

communications

Supported Versions:

(see Section 2.0)

Automated Attendant

Return to Operator

Message Waiting

Caller ID

Minimum Software:

Refer to Section 3.1

PSTN

PSTN

Avaya Tenovis

Integral-55 PBX

Message

Application

Server

1
2
3
...
»

Содержание Tenovis Integral-55


























Отзывы:

Нет отзывов