Avaya P332MF Скачать руководство пользователя страница 79

Страница: 79 / 182

Chapter 6

CLI – Layer 2

Avaya P332MF User’s Guide

show port auto-negotiation-flowcontrol-advertisement

Use the s

how port auto-negotiation-flowcontrol-advertisement

command to display the flowcontrol advertisement for a Gigabit port used to
perform auto-negotiation.

The syntax for this command is:

show port auto-negotiation-flowcontrol-advertisement

[<mod_num>[/<port_num>]]

Output Example:

P330-N> show port auto-negotiation-flowcontrol-advertisement

Port 1/1 advertises no flow control capabilities.

Port 1/2 advertises no flow control capabilities.

Port 1/3 advertises no flow control capabilities.

etc.

show trunk

Use the

show trunk

command to display VLAN tagging information of the

ports, port binding mode, and the port VLAN ID.

The syntax for this command is:

show trunk [<mod_num>[/<port_num>]]

Output Example:

P330-N> show trunk

Port Mode Binding mode Native vlan

------ ----- ----------------------------- -----------

1/1 dot1q bound to configured vlans 1

1/2 dot1q bound to all vlans 1

1/3 off statically bound 1

1/4 off statically bound 1

1/5 off statically bound 1

mod_num

Number of the switch

port num

Number of the port

Содержание P332MF























































































































































































Результаты поиска

Содержание P332MF

Отзывы:

Avaya P332MF, Руководство пользователя, Страница: 79 / 182

Результаты поиска

Содержание P332MF

Отзывы: