Avaya P332GT-ML Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 150

background image

Chapter 3

10

Avaya P332GT

-ML User’s Guide

Approved SFF/SFP GBIC Transceivers

The SFF/SFP GBIC (Gigabit Interface Converter) have been tested for use with the
Avaya

P332GT

-ML Gigabit Ethernet ports. For a list of approved SFF/SFP GBIC

transceivers, see: www.avayanetwork.com/

Note:

SFF/SFP GBIC transceivers are hot-swappable.

Safety Information

The SFF/SFP GBIC transceivers are Class 1 Laser products. They comply with
EN 60825-1 and Food and Drug Administration (FDA) 21 CFR 1040.10 and 1040.11.
The SFF/SFP GBIC transceivers must be operated under recommended operating
conditions.

Laser Classification

Note:

Class 1 lasers are inherently safe under reasonably foreseeable conditions of

operation.

Caution:

The use of optical instruments with this product will increase eye hazard.

Usage Restriction

When a SFF/SFP GBIC transceiver is inserted in the module but is not in use, the
Tx and Rx ports should be protected with an optical connector or a dust plug.

Caution:

Use only approved SFF/SFP GBIC transceivers. All approved SFF/SFP

GBIC transceivers:
1) Are 3.3V. Do

not

insert a 5V SFF/SFP GBIC.

2) Use Serial Identification. Do

not

use a GBIC that utilizes Parallel Identification.

CLASS 1

LASER PRODUCT

«
...
22
23
24
25
26
...
»

Содержание P332GT-ML























































































































































Отзывы:

Нет отзывов

Похожие инструкции для P332GT-ML

Бренд: FELA Страницы: 13

TotalStorage 3534-F08

Бренд: IBM Страницы: 105

RedBooks SAN24B-5

Бренд: IBM Страницы: 11

RedBooks SAN24B-5

Бренд: IBM Страницы: 2

Бренд: IBM Страницы: 123

8265 Nways ATM Switch

Бренд: IBM Страницы: 192

Бренд: IDEC Страницы: 8

Бренд: IDEM SAFETY SWITCHES Страницы: 2

Бренд: National Instruments Страницы: 32

Бренд: Panio Страницы: 5

Бренд: Cole Hersee Страницы: 2

LMP-1204G-SFP Series

Бренд: ANTAIRA Страницы: 20

2X2 VGA SWITCHER

Бренд: Gefen Страницы: 12

Бренд: Ruby Tech Страницы: 2

Бренд: JAR Systems Страницы: 2

Бренд: Surefire Страницы: 2

S6520X-EI Series

Бренд: H3C Страницы: 34

Бренд: JetNet Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды