manualshive.com logo in svg

Avaya ERS 3500 Series, Руководство пользователя

Поделиться
Скачать
Avaya ERS 3500 Series Скачать руководство пользователя страница 7

Chapter 1:  Introduction

Purpose of this document

This document describes how to select, install, and remove Small Form Factor Pluggable
(SFP) transceivers. This document also provides specifications for each supported device.

Related resources

Documentation

For a list of the documentation for this product, see 

Documentation Roadmap Reference for

Avaya Ethernet Routing Switch 3500 Series

, NN47203-101.

Training

Ongoing product training is available. For more information or to register, you can access the
Web site at 

http://avaya-learning.com

.

Avaya Mentor videos

Avaya Mentor videos provide technical content on how to install, configure, and troubleshoot
Avaya products.

About this task

Videos are available on the Avaya Support website, listed under the video document type, and

on the Avaya-run channel on YouTube.

Installing the SFP, SFP+, and XFP transceivers on Avaya ERS 3500 Series

March 2014     7

Содержание ERS 3500 Series











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды